Verified dimensional collection

Zero-clearance refrigerators with verified operating requirements

Zero clearance must describe a supported hinge or door behavior; it is not the same as minimal ventilation clearance.

Enter your finished opening

How to measure your opening

Measurements stay in this tab’s session storage. They are not sent to analytics.

This page remains unpublished until at least five complete models distinguish ventilation, wall clearance for a door open to 90°, door-open depth, and the reviewed zero-clearance endpoint.

Buying guide: zero-clearance refrigerators with verified operating requirements

Zero-clearance refrigerators use hinges that let the doors open without swinging outside the cabinet width, so they can sit flush against a wall or between cabinets. That is the property to check when the refrigerator goes into a tight corner or a run of tall cabinets.

Zero clearance describes the door swing, not the cavity: the appliance still needs the side, top and rear space its manufacturer specifies for air flow and installation. The reviewed requirements below separate those two questions.

What the verified measurements show

These 5 reviewed models come from 3 brands; the most represented are Haier (3), Bosch (1), GE (1). The opening width they need ranges from 22 1/16 in for the Bosch B09IB91NSP to 25 5/8 in for the GE GPV10FGNBB, with half needing 25 5/8 in or less. The cabinet-only depth runs from 19 1/2 in (Bosch B09IB91NSP) to 22 3/8 in (Haier HA10TG21SW). The height including the hinges runs from 59 1/2 in (Haier HA10TG21SB) to 69 3/4 in (Bosch B09IB91NSP). With a door open at 90 degrees, 5 of these models have a verified depth; the typical one reaches 47 3/16 in from the back of the fridge, and the deepest, the GE GPV10FGNBB, reaches 47 1/4 in. 5 models have a verified hinge-side wall clearance for the door to open 90 degrees: from 0 in to 0 in, typically 0 in.

What the reviewed dataset shows

Calculated from 5 evidence-qualified models in ExactFit’s 935-model catalog. Most recent included review: 2026-11-14. These are dataset findings, not estimates of the whole market.

Actual width22 in–23 5/8 in; median 23 5/8 in
Reviewed opening width22 1/16 in–25 5/8 in; median 25 5/8 in
Height with hinge59 1/2 in–69 3/4 in; median 59 1/2 in
Cabinet-only depth19 1/2 in–22 3/8 in; median 22 3/8 in

Compare 3 designs

5 model numbers, with colour and finish versions of the same fridge grouped into one row. Filter by size below; a model missing a measurement drops out while that filter is on. Required opening width is the maker’s printed cutout where there is one, otherwise the fridge’s width plus the side gaps the maker asks for.

3 of 3 designs shown. A model missing a filtered measurement is left out while that filter is on.

ExactFit-qualified models and reviewed measurement endpoints
ModelActual widthRequired opening widthDepth with doors open 90°Wall clearance, door at 90°Evidence
Bosch B09IB91NSPBottom Freezer · Built-in22 in22.0625 in44.88 in0 inReview
Haier HA10TG21SSTop Freezer · Standard-depth23.6 in25.6 in47.2 in0 inReview
GE GPV10FGNBBTop Freezer · Counter-depth23.625 in25.625 in47.25 in0 inReview

Measurements that matter

    Common fit problems

      Questions about this category

      Continue comparing by size and type

      Confirm current manufacturer specifications and installation requirements before purchase or installation. ExactFit does not evaluate every delivery-path, plumbing, electrical, trim, floor, or door-swing condition.