Measurement evidence for Haier HA10TG21SS

Value used by ExactFit

23.6 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 9-8-Cu-Ft-Top-Freezer-Refrigerator-HA10TG21SS
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Current exact-model Haier official weights and dimensions specification.
Reviewed: 2026-09-04

Current exact-model Haier official weights and dimensions specification.

Why this value was used

Current exact-model Haier official weights and dimensions specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

59 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 9-8-Cu-Ft-Top-Freezer-Refrigerator-HA10TG21SS
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Current exact-model Haier official weights and dimensions specification.
Reviewed: 2026-09-04

Current exact-model Haier official weights and dimensions specification.

Why this value was used

Current exact-model Haier official weights and dimensions specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

59.4 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 105166703.pdf
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Illustration table: A Height (with Hinge Cover) 59.40". The family quick specs page 1 also prints Height 59.40" (its page 2 table prints 59.50").

Why this value was used

Illustration table: A Height (with Hinge Cover) 59.40". The family quick specs page 1 also prints Height 59.40" (its page 2 table prints 59.50").

Other evidence found

• 59.5 in — superseded

  www.haierappliances.com; location not retained. Model scope: not separately recorded. Raw value: Overall Height: 59.5 in | - Haier Appliances Overall Depth, 25.20 in. Overall Depth with Handle, 25.3 in. Overall Height, 59.5 in. Overall Width, 23.6 in. Side Air Clearances, 1 in. Top Air Clearances, 1 . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.4 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 105166703.pdf
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Illustration table: D Case Depth Without Door 22.40". Printed identically in the HA10TG21SS quick specs and the HA10TG21SB/SS/SW quick specs; the previous 22 in came from a rounded web listing.

Why this value was used

Illustration table: D Case Depth Without Door 22.40". Printed identically in the HA10TG21SS quick specs and the HA10TG21SB/SS/SW quick specs; the previous 22 in came from a rounded web listing.

Other evidence found

• 22 in — superseded

  www.haierappliances.com; location not retained. Model scope: not separately recorded. Raw value: Current exact-model Haier official weights and dimensions specification.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.2 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 105166703.pdf
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Illustration table: C Depth (without handle) 25.20". The family quick specs page 1 also prints Depth 25.20" (its page 2 table prints 25.30"); the previous 25 in came from a rounded web listing.

Why this value was used

Illustration table: C Depth (without handle) 25.20". The family quick specs page 1 also prints Depth 25.20" (its page 2 table prints 25.30"); the previous 25 in came from a rounded web listing.

Other evidence found

• 25 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: Depth Without Handle = 25.0 in | ezer, 38 in ; Side Air Clearances, 1 in ; Approximate Shipping Weight, 132 lb ; Depth Without Handle, 25 in. | independent cached support: appliancehomestore.com, jeffsappliance.com. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25.3 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 9-8-Cu-Ft-Top-Freezer-Refrigerator-HA10TG21SS
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Current exact-model Haier official weights and dimensions specification.
Reviewed: 2026-09-04

Current exact-model Haier official weights and dimensions specification.

Why this value was used

Current exact-model Haier official weights and dimensions specification.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

47 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier measurement source — 9-8-Cu-Ft-Top-Freezer-Refrigerator-HA10TG21SS
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Current exact-model Haier official weights and dimensions specification.
Reviewed: 2026-09-04

Current exact-model Haier official weights and dimensions specification.

Why this value was used

Current exact-model Haier official weights and dimensions specification.

Other evidence found

• 47.2 in — superseded

  Document 105166703.pdf; page 2. Model scope: not separately recorded. Raw value: Depth (with door at 90°): 47.2 in | Depth (with door at 90°) | 47.20" | F. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

25.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 23.6 + 2 * 1

Confidence label: high.

Primary evidence

Haier measurement source — 9-8-Cu-Ft-Top-Freezer-Refrigerator-HA10TG21SS
Haier · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: HA10TG21 finish family opening width uses the exact current Haier closed envelope 23.6 in plus the e
Reviewed: 2026-09-04

HA10TG21 finish family opening width uses the exact current Haier closed envelope 23.6 in plus the exact Haier side air clearance 1 in on both sides: 23.6 + 2 * 1 = 25.6 in.

Why this value was used

HA10TG21 finish family opening width uses the exact current Haier closed envelope 23.6 in plus the exact Haier side air clearance 1 in on both sides: 23.6 + 2 * 1 = 25.6 in. Calculation or inference: 23.6 + 2 * 1.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

60.4 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Haier measurement source — 105166703.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-22

Haier specification sheet HA10TG21SS (7/20) p.2: A Height (with Hinge Cover) 59.40" plus Required Air Clearance Top 1" = 60.4 in. The stored 60.5 used an outdated 59.5 in height.

Why this value was used

Haier specification sheet HA10TG21SS (7/20) p.2: A Height (with Hinge Cover) 59.40" plus Required Air Clearance Top 1" = 60.4 in. The stored 60.5 used an outdated 59.5 in height. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

• 60.5 in — superseded

  www.haierappliances.com; location not retained. Model scope: not separately recorded. Raw value: HA10TG21 finish family opening height uses the tallest exact appliance endpoint 59.5 in plus exact top air clearance 1 in: 60.5 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.4 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 22.4 + 2 = 24.4

Confidence label: high.

Primary evidence

Haier measurement source — Haier_HA10TG21_quickspecs_2026-10-31.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-31

Haier HA10TG21 quick specs: "D Case Depth Without Door 22.40"" and clearances "Back 2"". Opening depth = 22.4 + 2 = 24.4 in. The earlier figure used 22 in instead of the printed 22.40 (Codex measurement review 2026-10-31).

Why this value was used

Haier HA10TG21 quick specs: "D Case Depth Without Door 22.40"" and clearances "Back 2"". Opening depth = 22.4 + 2 = 24.4 in. The earlier figure used 22 in instead of the printed 22.40 (Codex measurement review 2026-10-31). Calculation or inference: 22.4 + 2 = 24.4.

Other evidence found

• 24 in — superseded

  www.haierappliances.com; location not retained. Model scope: not separately recorded. Raw value: HA10TG21 finish family opening depth uses exact case-only depth 22 in plus exact rear air clearance 2 in: 22 + 2 = 24 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Haier measurement source — 105166705.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics

Confidence label: high.

Primary evidence

Haier measurement source — 105166705.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 10
Reviewed: 2026-09-05

Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.

Why this value was used

Legacy reviewed field migration; endpoint indicators=['each side', 'clearance at each side']; Installation manual specifies 1 inch minimum clearance at each side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern HA10TG21****

Confidence label: high.

Primary evidence

Haier measurement source — fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

clearances top 1"

Why this value was used

clearances top 1" Calculation or inference: documented DOE model pattern HA10TG21****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern HA10TG21****

Confidence label: high.

Primary evidence

Haier measurement source — fb11578f6a2030f09d52b55c7c045a335cdfbcd0.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

clearances top 1" back 2"

Why this value was used

clearances top 1" back 2" Calculation or inference: documented DOE model pattern HA10TG21****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

23.6 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Haier installation document — 105166703.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width 23.60"

Why this value was used

Overall Width 23.60"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.