Measurement evidence for Bosch B09IB91NSP

Value used by ExactFit

22 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in.

Why this value was used

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 74747658.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Appliance dimensions H x W x D: 69 3/4" x 22" x 21 1/2"; flat concealed hinge stays within the appliance envelope.

Why this value was used

Appliance dimensions H x W x D: 69 3/4" x 22" x 21 1/2"; flat concealed hinge stays within the appliance envelope.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in; page-2 product drawing labels overall height 69 3/4 in.

Why this value was used

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in; page-2 product drawing labels overall height 69 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

19.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — bosch-800-series-built-in-bottom-freezer-refrigerator-custom-panel-9-cu-ft-b09ib91nsp-30855301
www.rona.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model specification: Depth (Less Door) 19.5 in. Replaces an unrelated 36-inch oven/cooktop mat
Reviewed: 2026-09-04

Exact-model specification: Depth (Less Door) 19.5 in. Replaces an unrelated 36-inch oven/cooktop match.

Why this value was used

Exact-model specification: Depth (Less Door) 19.5 in. Replaces an unrelated 36-inch oven/cooktop match.

Other evidence found

• 36 in — superseded

  askboschlowes.com; location not retained. Model scope: not separately recorded. Raw value: d: c: b: a: the built-in oven can be installed below the electric cooktop as long as there is no contact between the bottom of the cooktop and the top of the oven dimensions based on standard countertop height: 36″ (914 mm) with 43/4″ (121 mm) toe kick including base plate cooktop conduit fitting built-in oven cooktop 30" (762 mm) built-in oven - under electric cooktop measurements in inches (mm) (a) 5 (125) (c) 4 (100) 61/16 (169) 281/4 (718) 43/4 (121) 245/8 (625) 269/16 (674) 36 (915) 29 (737) 3 (76) 13/16 (21) (d) (b) 30" (762 mm) built-in oven - under electric cooktop measurements in inches (mm) (a) 5 (125) (c) 4 (100) 61/16 (169) 281/4 (718) 245/8 (625) 269/16 (674) 36 (915) 29 (737) 3 (76) 13/16 (21) (d) (b) c: d: b: a: this distance can be smaller, check installation instructions of ventilation hood min. distance from the cooktop cut-out to the side wall min. distance between the surface of the cooktop and the underside of the ventilation hood max. recessed depth min. distance . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

21.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — bosch-800-series-built-in-bottom-freezer-refrigerator-custom-panel-9-cu-ft-b09ib91nsp-30855301
www.rona.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model specification: Depth (Excluding Handles) 21.5 in.
Reviewed: 2026-09-04

Exact-model specification: Depth (Excluding Handles) 21.5 in.

Why this value was used

Exact-model specification: Depth (Excluding Handles) 21.5 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

21.5 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: published 21.5 in closed depth + 0 in handle projection in Bosch-documented handleless soft-close configuration

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model Bosch sheet prints appliance depth 21 1/2 in and Soft close capability: Yes; the same retained sheet permits handleless panels on soft-close units. The standardized handleless configuration therefore has an exact handle-inclusive envelope of 21 1/2 in.

Why this value was used

Exact-model Bosch sheet prints appliance depth 21 1/2 in and Soft close capability: Yes; the same retained sheet permits handleless panels on soft-close units. The standardized handleless configuration therefore has an exact handle-inclusive envelope of 21 1/2 in. Calculation or inference: published 21.5 in closed depth + 0 in handle projection in Bosch-documented handleless soft-close configuration.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

44.88 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — bosch-800-series-built-in-bottom-freezer-refrigerator-custom-panel-9-cu-ft-b09ib91nsp-30855301
www.rona.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model specification: Depth with Door Open 44.88 in.
Reviewed: 2026-09-04

Exact-model specification: Depth with Door Open 44.88 in.

Why this value was used

Exact-model specification: Depth with Door Open 44.88 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

22.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch installation document — 74747658.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Required cutout size H x W x D: 70" x 22 1/16" x 22 1/16". Replaces an unrelated 30-inch cooktop match.

Why this value was used

Required cutout size H x W x D: 70" x 22 1/16" x 22 1/16". Replaces an unrelated 30-inch cooktop match.

Other evidence found

• 30 in — superseded

  askboschlowes.com; location not retained. Model scope: not separately recorded. Raw value: planning checklist planning checklist benchmark® series built-in refrigeration build your custom column benchmark® series built-in refrigeration this custom product requires attention to the finest details. carefully review all planning information, installation details and considerations and all dimensional information. did you remember to…?  choose a desired configuration - side-by-side or stand- alone columns  plan the cutout height(s) - 84"  plan the cutout width(s) - depends on configuration and column width  plan the cutout depth - 25" for north american style cabinets, 24" with installation frame accessory, 24" for european style cabinets  ensure the cutout interior (top and sides) is flush to the appliance at a depth of min. 4", preferably 6" from face frame  ensure the cutout interior returns (top and sides) are finished to match exterior at a depth of min. 4", preferably 6" from face frame  ensure proper clearance for appliance doors including handle(s) - check for in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — 74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

cutout size (H x W x D) 70"

Why this value was used

cutout size (H x W x D) 70"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

22.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact-model Bosch specification sheet: Required cutout size (H x W x D) = 70 x 22 1/16 x 22 1/16 in; page-2 cutout drawing repeats depth 22 1/16 in.

Why this value was used

Exact-model Bosch specification sheet: Required cutout size (H x W x D) = 70 x 22 1/16 x 22 1/16 in; page-2 cutout drawing repeats depth 22 1/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.03125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (22.0625 - 22) / 2

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints a 22 1/16 in opening and a 22 in appliance width; centered per-side residual is exactly 1/32 in.

Why this value was used

Exact-model sheet prints a 22 1/16 in opening and a 22 in appliance width; centered per-side residual is exactly 1/32 in. Calculation or inference: (22.0625 - 22) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.03125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (22.0625 - 22) / 2

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints a 22 1/16 in opening and a 22 in appliance width; centered per-side residual is exactly 1/32 in.

Why this value was used

Exact-model sheet prints a 22 1/16 in opening and a 22 in appliance width; centered per-side residual is exactly 1/32 in. Calculation or inference: (22.0625 - 22) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 70 - 69.75

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints a 70 in required cutout height and 69 3/4 in appliance height; exact residual is 1/4 in.

Why this value was used

Exact-model sheet prints a 70 in required cutout height and 69 3/4 in appliance height; exact residual is 1/4 in. Calculation or inference: 70 - 69.75.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 22.0625 - 21.5

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-11

Exact-model sheet prints a 22 1/16 in required cutout depth and 21 1/2 in closed handleless appliance depth; exact imperial residual is 9/16 in. This supersedes the rounded metric conversion.

Why this value was used

Exact-model sheet prints a 22 1/16 in required cutout depth and 21 1/2 in closed handleless appliance depth; exact imperial residual is 9/16 in. This supersedes the rounded metric conversion. Calculation or inference: 22.0625 - 21.5.

Other evidence found

• 0.547 in — superseded

  Document 74747665.pdf; page 7. Model scope: not separately recorded. Raw value: Recommended 22.047 in cavity minus 21.5 in handleless appliance depth = 0.547 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Bosch measurement source — 74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (zero-clearance hinge). Manufacturer specification: fully flush, zero-clearance hinge.

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (zero-clearance hinge). Manufacturer specification: fully flush, zero-clearance hinge.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

22 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bosch measurement source — B09IB91NSP-74747658.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-10

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in; page-2 product drawing also labels width 22 in.

Why this value was used

Exact-model Bosch specification sheet: Appliance dimensions (H x W x D) = 69 3/4 x 22 x 21 1/2 in; page-2 product drawing also labels width 22 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.