Measurement evidence for KitchenAid KRFF136SPS

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid measurement source — 105605088.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-31

KitchenAid dimension table, column KRFF136S*: "H Width of cabinet 35 7/8". The stored 35 5/8 was the KBFS20EC* column.

Why this value was used

KitchenAid dimension table, column KRFF136S*: "H Width of cabinet 35 7/8". The stored 35 5/8 was the KBFS20EC* column.

Other evidence found

• 35.625 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Aligned with case_width_in (35.625"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height - Top of Cabinet: 68 7/8 in for KRFF136S*

Why this value was used

Height - Top of Cabinet: 68 7/8 in for KRFF136S*

Other evidence found

• 68.5 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Height to top of cabinet 68¹/2" (174 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall Height 701/8" (178.1 cm)

Why this value was used

Overall Height 701/8" (178.1 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Cabinet Only: 29 1/8 in for KRFF136S*

Why this value was used

Depth - Cabinet Only: 29 1/8 in for KRFF136S*

Other evidence found

• 24.125 in — superseded

  Document 105605088.pdf (p.5); page 5. Model scope: not separately recorded. Raw value: Depth of cabinet only -> 241/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Without Handles: 33 in for KRFF136S*

Why this value was used

Depth - Without Handles: 33 in for KRFF136S*

Other evidence found

• 28 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Depth without handles 28" (71.1 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - With Handles: 35 1/2 in for KRFF136S*

Why this value was used

Depth - With Handles: 35 1/2 in for KRFF136S*

Other evidence found

• 29.375 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with handles 293/8" (74.6 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Doors Open 90 degrees: 48 1/8 in for KRFF136S*

Why this value was used

Depth - Doors Open 90 degrees: 48 1/8 in for KRFF136S*

Other evidence found

• 43 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Depth with doors open 90° 43" (109.2 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.875 + 2 * 0.5 = 36.875

Confidence label: high.

Primary evidence

KitchenAid measurement source — 105605088.pdf
www.theapplianceshoppe.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-31

Width of cabinet 35 7/8 in (KRFF136S* column) plus the 1/2 in of space on each side the KitchenAid guide asks for = 36 7/8 in.

Why this value was used

Width of cabinet 35 7/8 in (KRFF136S* column) plus the 1/2 in of space on each side the KitchenAid guide asks for = 36 7/8 in. Calculation or inference: 35.875 + 2 * 0.5 = 36.875.

Other evidence found

• 36 in — superseded

  www.theapplianceshoppe.com; location not retained. Model scope: not separately recorded. Raw value: Exact model listing: Cutout Width 36.0 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 36.625 in — superseded

  www.kitchenaid.com; page 2. Model scope: not separately recorded. Raw value: KitchenAid's installation documents for KRFF136SPS print no cutout width; they ask for 1/2 in of space on each side: guide: '1/2" space on each side' Opening width = 35.625 + 1/2 + 1/2 = 36.625 in. The earlier 36.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

KitchenAid measurement source — dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

KitchenAid measurement source — 105605088.pdf
KitchenAid · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Recomputed after corrected case-only depth: 29 1/8 + 1 rear clearance = 30 1/8 in

Why this value was used

Recomputed after corrected case-only depth: 29 1/8 + 1 rear clearance = 30 1/8 in Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF136SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF136SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF136SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern KRFF136SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF136SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" space on each side and at the top

Why this value was used

1/2" space on each side and at the top Calculation or inference: documented DOE model pattern KRFF136SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern KRFF136SP***

Confidence label: high.

Primary evidence

KitchenAid measurement source — dimension-guide-w11808663-reva.pdf
KitchenAid · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern KRFF136SP***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

KitchenAid measurement source — 105605082.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 8
Reviewed: 2026-10-25

Exact-model installation instructions: "When installing your refrigerator next to a fixed wall, leave 21/2" (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open." Door angle not stated; recorded as the 90° wall clearance as for other models with this wording.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Exact-model installation instructions: "When installing your refrigerator next to a fixed wall, leave 21/2" (6.3 cm) minimum on the hinge side (some models require more) to allow for the door to swing open." Door angle not stated; recorded as the 90° wall clearance as for other models with this wording.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

KitchenAid installation document — 105605088.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width - Cabinet: 35 7/8 in for KRFF136S*

Why this value was used

Width - Cabinet: 35 7/8 in for KRFF136S*

Other evidence found

• 35.625 in — superseded

  Document 105605088.pdf; page 1. Model scope: not separately recorded. Raw value: Width of cabinet 355/8" (90.5 cm). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.