This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-29. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 36.375 in | ✓ Verified — retained secondary source | KitchenAid installation document — 105602630.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit36.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid installation document — 105602630.pdf Visual product-dimensions table: Overall Width = 36 3/8 in.Open original source ↗ Why this value was usedVisual product-dimensions table: Overall Width = 36 3/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.25 in | ✓ Verified — exact model | KitchenAid measurement source — p.KBSD736SPS.html KitchenAid | Retained specification excerpt: Height To Top Of Cabinet: 83.25 in | 5 in Freezer Capacity Volume 7.3 cu. ft. Gross Weight 566.5 lbs | |
Value used by ExactFit83.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — p.KBSD736SPS.html Height To Top Of Cabinet: 83.25 in | 5 in Freezer Capacity Volume 7.3 cu. ft. Gross Weight 566.5 lbs Height 83.25 in Height To Top Of Cabinet 83.25 in Maximum Height 83.375 in Net Weight 538.17 lbs Refrigerator Capacity Volume 13.Open original source ↗ Why this value was usedHeight To Top Of Cabinet: 83.25 in | 5 in Freezer Capacity Volume 7.3 cu. ft. Gross Weight 566.5 lbs Height 83.25 in Height To Top Of Cabinet 83.25 in Maximum Height 83.375 in Net Weight 538.17 lbs Refrigerator Capacity Volume 13. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.25 in | ✓ Verified — retained secondary source | KitchenAid installation document — 105602630.pdf assets.skulytics.io | Page 25 | |
Value used by ExactFit83.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid installation document — 105602630.pdf Overall Height: 83.25 in | Overall Height | 831/4" (2115 mm) | GOpen original source ↗ Why this value was usedOverall Height: 83.25 in | Overall Height | 831/4" (2115 mm) | G Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 22.4 in | ✓ Verified — exact model | KitchenAid measurement source — p.KBSD736SPS.html KitchenAid | Retained specification excerpt: Depth Excluding Doors: 22.4 in | Depth Closed Excluding Handles 25.81 in Depth Closed Including Han | |
Value used by ExactFit22.4 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — p.KBSD736SPS.html Depth Excluding Doors: 22.4 in | Depth Closed Excluding Handles 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 7.3 cu. ft. GroOpen original source ↗ Why this value was usedDepth Excluding Doors: 22.4 in | Depth Closed Excluding Handles 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 7.3 cu. ft. Gro Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 25.81 in | ✓ Verified — exact model | KitchenAid measurement source — p.KBSD736SPS.html KitchenAid | Retained specification excerpt: Depth Closed Excluding Handles: 25.81 in | t. Cutout Depth 24 in Cutout Height 83.5 in Cutout Width | |
Value used by ExactFit25.81 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — p.KBSD736SPS.html Depth Closed Excluding Handles: 25.81 in | t. Cutout Depth 24 in Cutout Height 83.5 in Cutout Width 35.5 in Depth 27.75 in Depth Closed Excluding Handles 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth WithOpen original source ↗ Why this value was usedDepth Closed Excluding Handles: 25.81 in | t. Cutout Depth 24 in Cutout Height 83.5 in Cutout Width 35.5 in Depth 27.75 in Depth Closed Excluding Handles 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth With Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27.75 in | ✓ Conflicting sources — resolved | KitchenAid installation document — 105602630.pdf assets.skulytics.io | Page 6 | |
Value used by ExactFit27.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid installation document — 105602630.pdf Visual product-dimensions table: Depth with handles = 27 3/4 in.Open original source ↗ Why this value was usedVisual product-dimensions table: Depth with handles = 27 3/4 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.75 in | ✓ Verified — exact model | KitchenAid measurement source — p.KBSD736SPS.html KitchenAid | Retained specification excerpt: Depth With Door Open 90: 43.75 in | s 25.81 in Depth Closed Including Handles 27.7 in Depth Excludin | |
Value used by ExactFit43.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — p.KBSD736SPS.html Depth With Door Open 90: 43.75 in | s 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 7.3 cu. ft. Gross Weight 566.5 lbs Height 83.25 in HeigOpen original source ↗ Why this value was usedDepth With Door Open 90: 43.75 in | s 25.81 in Depth Closed Including Handles 27.7 in Depth Excluding Doors 22.4 in Depth With Door Open 90 Degree 43.75 in Freezer Capacity Volume 7.3 cu. ft. Gross Weight 566.5 lbs Height 83.25 in Heig Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 35.5 in | ✓ Verified — retained secondary source | KitchenAid installation document — 105602630.pdf assets.skulytics.io | Page 9 | |
Value used by ExactFit35.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid installation document — 105602630.pdf Exact 36-inch model installation table: Opening Width (W) = 35 1/2" to 35 3/4"; minimum recorded.Open original source ↗ Why this value was usedExact 36-inch model installation table: Opening Width (W) = 35 1/2" to 35 3/4"; minimum recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 83.25 in | ✓ Verified — exact model | KitchenAid measurement source — 105602630.pdf KitchenAid | Page 9 | |
Value used by ExactFit83.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — 105602630.pdf Installation: Top Grille Clearance 83 1/4" minimum, 84 3/4" maximum (84" recommended), for every installation type.Open original source ↗ Why this value was usedInstallation: Top Grille Clearance 83 1/4" minimum, 84 3/4" maximum (84" recommended), for every installation type. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — exact model | KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-side-by-side-refrigerator-features-exterior-water-and-ice-dispenser-with-measured-fill.kbsd736sps.html KitchenAid | Retained specification excerpt: Cutout Depth 24 in | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceKitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-side-by-side-refrigerator-features-exterior-water-and-ice-dispenser-with-measured-fill.kbsd736sps.html Cutout Depth 24 inOpen original source ↗ Why this value was usedCutout Depth 24 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.188 in | ≈ Estimated — not printed for this model | ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (KitchenAid doesn't print this for the model) Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.188 in | ≈ Estimated — not printed for this model | ExactFit estimate (KitchenAid doesn't print this for the model) ExactFit | Not printed for this model | |
Value used by ExactFit0.188 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical KitchenAid side gap (estimate) Confidence label: low. Primary evidenceExactFit estimate (KitchenAid doesn't print this for the model) Not printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was usedNot printed in the KitchenAid documents we have for this model. 3/16 in is the side gap KitchenAid prints for similar models (KRFC236SBE, KRFC236SJP, KRFC236SPS), so it is shown as an estimate. The fit check uses KitchenAid's cutout width for this model, so this estimate does not change the fit answer. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.75 in | ✓ Verified — retained secondary source | KitchenAid installation document — 105602630.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit0.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid installation document — 105602630.pdf Exact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille.Open original source ↗ Why this value was usedExact-model installation guide: A clearance of 3/4" (19 mm) must be maintained above the top grille. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1.6 in | ✓ Verified — exact model · Calculated/inferred | KitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-side-by-side-refrigerator-features-exterior-water-and-ice-dispenser-with-measured-fill.kbsd736sps.html KitchenAid | Retained specification excerpt: KitchenAid built-in opening residual: 24.0 - 22.4 = 1.6 in behind the case within the accepted openi | |
Value used by ExactFit1.6 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: medium. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceKitchenAid measurement source — p.20.8-cu.-ft.-36-built-in-side-by-side-refrigerator-features-exterior-water-and-ice-dispenser-with-measured-fill.kbsd736sps.html KitchenAid built-in opening residual: 24.0 - 22.4 = 1.6 in behind the case within the accepted opening.Open original source ↗ Why this value was usedKitchenAid built-in opening residual: 24.0 - 22.4 = 1.6 in behind the case within the accepted opening. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.75 in | ? Verified — finalized database measurement | KitchenAid measurement source — 105602630.pdf Publisher not recorded | Page 28 | |
Value used by ExactFit2.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — 105602630.pdf Exact-model KitchenAid installation guide, 36" model, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to each open door. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedExact-model KitchenAid installation guide, 36" model, 90° door swing: A = 2 3/4" (69.9 mm) from the cabinet side to each open door. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35 in | ✓ Conflicting sources — resolved | KitchenAid measurement source — https://www.kitchenaid.com/ KitchenAid | Retained specification excerpt: Official exact-model page: Cabinet Width 35 in; prior unverified value was overall trim width. | |
Value used by ExactFit35 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceKitchenAid measurement source — https://www.kitchenaid.com/ Official exact-model page: Cabinet Width 35 in; prior unverified value was overall trim width.Open original source ↗ Why this value was usedOfficial exact-model page: Cabinet Width 35 in; prior unverified value was overall trim width. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 27.75 in. Earlier retained values: 27.7 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Visual product-dimensions table: Depth with handles = 27 3/4 in.
View source scope, location, and impact on fitSelected: 35 in. Earlier retained values: 36.375 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Official exact-model page: Cabinet Width 35 in; prior unverified value was overall trim width.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-25.
7 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth with handle; Minimum cutout width; Minimum cutout height; Top clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL unavailable in the record.
KitchenAid · Web source · exact model/source
Model numbers covered: KBSD736SPS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
4 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗KitchenAid · Web source · exact model/source
Model numbers covered: KBSD736SPS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗KitchenAid · Web source · exact model/source
Model numbers covered: KBSD736SPS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-29. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.