Measurement evidence for GE GDE25EYKFS

Value used by ExactFit

32.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width (in.) H 32-3/4
Reviewed: 2026-09-09

Width (in.) H 32-3/4

Why this value was used

Width (in.) H 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to top of case (in.) C 68-5/8
Reviewed: 2026-09-09

Height to top of case (in.) C 68-5/8

Why this value was used

Height to top of case (in.) C 68-5/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to top of hinge (in.) B 69-3/4
Reviewed: 2026-09-09

Height to top of hinge (in.) B 69-3/4

Why this value was used

Height to top of hinge (in.) B 69-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

30.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Case depth without door (in.) D 30-5/8
Reviewed: 2026-09-09

Case depth without door (in.) D 30-5/8

Why this value was used

Case depth without door (in.) D 30-5/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

35 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Case depth less door handle (in.) E 35
Reviewed: 2026-09-09

Case depth less door handle (in.) E 35

Why this value was used

Case depth less door handle (in.) E 35

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

37.5 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Case depth with door handle (in.) F 37-1/2
Reviewed: 2026-09-09

Case depth with door handle (in.) F 37-1/2

Why this value was used

Case depth with door handle (in.) F 37-1/2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

65.125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with fresh food door open 90° (in.) G 65-1/8
Reviewed: 2026-09-09

Depth with fresh food door open 90° (in.) G 65-1/8

Why this value was used

Depth with fresh food door open 90° (in.) G 65-1/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance; Cabinet case width;

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, si
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, side_ventilation_clearance_in=0.125; result=33 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: case_width_in=32.75, side_ventilation_clearance_in=0.125; result=33 in. Calculation or inference: case_width_in + 2 * side_ventilation_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Top clearance;

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.75,
Reviewed: 2026-09-09

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.75, top_clearance_in=1; result=70.75 in.

Why this value was used

GE additive installation-envelope calculation from high-confidence operands: height_hinge_in=69.75, top_clearance_in=1; result=70.75 in. Calculation or inference: height_hinge_in + top_clearance_in.

Other evidence found

• 70.875 in — superseded

  data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf; page 1. Model scope: not separately recorded. Raw value: {"calculation": "69.875 + top_clearance_in", "operands": {"top_clearance_in": [{"cache_path": "data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf", "page": "PDF page 1, AIR CLEARANCES table", "raw": "Top (in.) 1", "source_url": "https://images.salsify.com/image/upload/s--HmDgrJE_--/b24917182a5b730c868364c891db4cae8ded37d0.pdf", "value_in": 1.0}]}, "result_in": 70.875}. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: {"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cach
Reviewed: 2026-09-09

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf", "page": "PDF page 1, OVERALL DIMENSIONS row D", "raw": "Case depth without door (in.) D 30-5/8", "source_url": "https://images.salsify.com/image/upload/s--HmDgrJE_--/b24917182a5b730c868364c891db4cae8ded37d0.pdf", "value_in": 30.625}], "rear_clearance_in": [{"cache_path": "data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf", "page": "PDF page 1, AIR CLEARANCES table", "raw": "Back (in.) 2", "source_url": "https://images.salsify.com/image/upload/s--HmDgrJE_--/b24917182a5b730c868364c891db4cae8ded37d0.pdf", "value_in": 2.0}]}, "result_in": 32.625}

Why this value was used

{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf", "page": "PDF page 1, OVERALL DIMENSIONS row D", "raw": "Case depth without door (in.) D 30-5/8", "source_url": "https://images.salsify.com/image/upload/s--HmDgrJE_--/b24917182a5b730c868364c891db4cae8ded37d0.pdf", "value_in": 30.625}], "rear_clearance_in": [{"cache_path": "data/sources/GE/GDE25EYKFS/quick-specs-rev-08-21.pdf", "page": "PDF page 1, AIR CLEARANCES table", "raw": "Back (in.) 2", "source_url": "https://images.salsify.com/image/upload/s--HmDgrJE_--/b24917182a5b730c868364c891db4cae8ded37d0.pdf", "value_in": 2.0}]}, "result_in": 32.625} Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Each side (in.) 1/8
Reviewed: 2026-09-09

Each side (in.) 1/8

Why this value was used

Each side (in.) 1/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Each side (in.) 1/8
Reviewed: 2026-09-09

Each side (in.) 1/8

Why this value was used

Each side (in.) 1/8

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Top (in.) 1
Reviewed: 2026-09-09

Top (in.) 1

Why this value was used

Top (in.) 1

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Back (in.) 2
Reviewed: 2026-09-09

Back (in.) 2

Why this value was used

Back (in.) 2

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 36.875 - 32.75

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
GE · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

{"calculation": "36.875 - 32.75", "operands": {}, "result_in": 4.125}

Why this value was used

{"calculation": "36.875 - 32.75", "operands": {}, "result_in": 4.125} Calculation or inference: 36.875 - 32.75.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
images.salsify.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Width (in.) H 32-3/4
Reviewed: 2026-09-09

Width (in.) H 32-3/4

Why this value was used

Width (in.) H 32-3/4

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

4.125 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 36.875 - 32.75

Confidence label: high.

Primary evidence

GE measurement source — quick-specs-rev-08-21.pdf
GE · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-09

{"calculation": "36.875 - 32.75", "operands": {}, "result_in": 4.125}

Why this value was used

{"calculation": "36.875 - 32.75", "operands": {}, "result_in": 4.125} Calculation or inference: 36.875 - 32.75.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.