This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-26. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Unanimous same-family value 31.625 in from WRTX5328PW; at least five existing product dimensions mat
Value used by ExactFit
31.625 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: same finish/model family (WRTX5328P) propagation from WRTX5328PW
Confidence label: medium.
Primary evidence
Whirlpool measurement source — Whirlpool_WRTX5328PW_Top_Freezer_Refrigerators_Whirlpool_WRTX5328PW.html www.canadianappliance.ca · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Unanimous same-family value 31.625 in from WRTX5328PW; at least five existing product dimensions mat Reviewed: 2026-09-04
Unanimous same-family value 31.625 in from WRTX5328PW; at least five existing product dimensions match and none conflict. Donor evidence: Exact-model cached specification: Depth Without Handles = 31.625 in | xterior Width 28 inches (rounded listing) Cabinet Depth 28 1/2 inches (approx.) Depth Without Handles 31 5/8 inches (approx.) Depth With Door Open 90° 57 inches (approx.) Height Without Hinges 65
Unanimous same-family value 31.625 in from WRTX5328PW; at least five existing product dimensions match and none conflict. Donor evidence: Exact-model cached specification: Depth Without Handles = 31.625 in | xterior Width 28 inches (rounded listing) Cabinet Depth 28 1/2 inches (approx.) Depth Without Handles 31 5/8 inches (approx.) Depth With Door Open 90° 57 inches (approx.) Height Without Hinges 65 Calculation or inference: same finish/model family (WRTX5328P) propagation from WRTX5328PW.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Dimension guide lists cabinet width 28" (page 1) and recommends 1/2" space on each side (page 2). Calculation or inference: 28 + 2 * 0.5 = 29 inches.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — 105530236.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-26
Recalculated 2026-09-26 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 65.375, height_hinge_in = 66.625, top_clearance_in = 0.5 = 67.125 in (previously 68.125 in).
Recalculated 2026-09-26 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 65.375, height_hinge_in = 66.625, top_clearance_in = 0.5 = 67.125 in (previously 68.125 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
68.125 in — superseded
The same document as the value used above; page 5. Model scope: not separately recorded. Raw value: Whirlpool opening envelope: max(65.375, 66.625) + 1.5 = 68.125 in.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool opening envelope: 27.625 + 1.0 = 28.625 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRTX5328P***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11685532-revB.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRTX5328P***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRTX5328P***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11685532-revB.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRTX5328P***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105527828.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-26
Location Requirements: 1/2 in recommended between overhead cabinets and the refrigerator top, and 1/2 in at each side. The stored 1 1/2 in came from the generic multi-model owner's manual.
Location Requirements: 1/2 in recommended between overhead cabinets and the refrigerator top, and 1/2 in at each side. The stored 1 1/2 in came from the generic multi-model owner's manual.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. LOCATION REQUIREMENTS To ensure proper ventilation for your refrigerator, it is recommended to allow a 1/2" (1.25 cm) space on each side and between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your refrigerator has an ice
Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. LOCATION REQUIREMENTS To ensure proper ventilation for your refrigerator, it is recommended to allow a 1/2" (1.25 cm) space on each side and between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your refrigerator has an ice
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105530238.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 67.125 in. Earlier retained values: 68.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Recalculated 2026-09-26 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 65.375, height_hinge_in = 66.625, top_clearance_in = 0.5 = 67.125 in (previously 68.125 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Model numbers covered: WRTX5328PM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout depth; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-26. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
