Measurement evidence for Whirlpool WRTX3319SZ

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Aligned with case_width_in (29.5")

Why this value was used

Aligned with case_width_in (29.5")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

65.4375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height to top of cabinet = 65-7/16 in.

Why this value was used

Height to top of cabinet = 65-7/16 in.

Other evidence found

• 65.437 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Height to top of cabinet 1662.1 mm (657/16"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.1875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall height = 66-3/16 in.

Why this value was used

Overall height = 66-3/16 in.

Other evidence found

• 66.189 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Overall Height 1681.2 mm (663/16"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Cabinet depth only = 28-3/8 in.

Why this value was used

Cabinet depth only = 28-3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — p.whirlpool-30-inch-wide-top-freezer-refrigerator-with-total-coverage-cooling-19-cu.-ft.wrtx3319sz.html
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Excluding Handles: 32.25 in | inge No Reversible Door Yes ### Dimensions Cabinet Width
Reviewed: 2026-09-04

Depth Closed Excluding Handles: 32.25 in | inge No Reversible Door Yes ### Dimensions Cabinet Width 29.5 in Depth 32.25 in Depth Closed Excluding Handles 32.25 in Depth Closed Including Handles 32.25 in Depth Excluding Doors 28.375 in Depth W

Why this value was used

Depth Closed Excluding Handles: 32.25 in | inge No Reversible Door Yes ### Dimensions Cabinet Width 29.5 in Depth 32.25 in Depth Closed Excluding Handles 32.25 in Depth Closed Including Handles 32.25 in Depth Excluding Doors 28.375 in Depth W

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

32.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Overall depth = 32-1/4 in.

Why this value was used

Overall depth = 32-1/4 in.

Other evidence found

• 32.252 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Overall Depth 819.2 mm (321/4"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

59.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with door open 90° = 59-7/8 in.

Why this value was used

Depth with door open 90° = 59-7/8 in.

Other evidence found

• 59.874 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Depth with door open 90° 1520.8 mm (597/8"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 29.5 + 2 * 0.5

Confidence label: medium.

Primary evidence

Whirlpool measurement source — 105606023.pdf + 105606023.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Minimum opening derived from exact product width plus explicit symmetric side spacing: 29.5 + 2 * 0.5 = 30.5 in. Side evidence: allow 1/2" (1.25 cm) of space on each side

Why this value was used

Minimum opening derived from exact product width plus explicit symmetric side spacing: 29.5 + 2 * 0.5 = 30.5 in. Side evidence: allow 1/2" (1.25 cm) of space on each side Calculation or inference: 29.5 + 2 * 0.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.6875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — 105606023.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Whirlpool opening envelope: max(65.4375, 66.1875) + 1.5 = 67.6875 in.

Why this value was used

Whirlpool opening envelope: max(65.4375, 66.1875) + 1.5 = 67.6875 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — 105606023.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Whirlpool opening envelope: 28.375 + 1.0 = 29.375 in.

Why this value was used

Whirlpool opening envelope: 28.375 + 1.0 = 29.375 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRTX3319S***

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-w11656229-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern WRTX3319S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRTX3319S***

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-w11656229-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern WRTX3319S***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, allow 1/2" (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1"

Why this value was used

Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, allow 1/2" (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your

Why this value was used

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. (1.25 cm) of space on each side. Allow 11/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall. If your

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1.5625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105605413.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-21

Dimension guide W11656229A (WRTX3019S*, WRTX3319S*, WRTX3219S*, WRTX5419S*, WRTX5519S*, WRTX3119S*): G, door opening clearance = 1 9/16 in (39 mm). Owner decision 2026-10-21: use this model's own printed opening clearance as the wall clearance at 90 degrees and the hinge-side wall gap, replacing the 2 in borrowed from the WRT519SZDT manual.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Dimension guide W11656229A (WRTX3019S*, WRTX3319S*, WRTX3219S*, WRTX5419S*, WRTX5519S*, WRTX3119S*): G, door opening clearance = 1 9/16 in (39 mm). Owner decision 2026-10-21: use this model's own printed opening clearance as the wall clearance at 90 degrees and the hinge-side wall gap, replacing the 2 in borrowed from the WRT519SZDT manual.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.5 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105606023.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width of cabinet 749.3 mm (291/2")

Why this value was used

Width of cabinet 749.3 mm (291/2")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.