Measurement evidence for Whirlpool WRT518SZFG

Value used by ExactFit

28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

H x W x D) 67-7/16" x 28" x 31-5/8"

Why this value was used

H x W x D) 67-7/16" x 28" x 31-5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

67.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Why this value was used

exact manufacturer sheet distinguishes appliance endpoint from cutout or overall endpoint

Other evidence found

• 67.4375 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: H x W x D) 67-7/16" x 28" x 31-5/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height - Overall = 68-1/4 in; cabinet height = 67-1/8 in.

Why this value was used

Height - Overall = 68-1/4 in; cabinet height = 67-1/8 in.

Other evidence found

• 67.4375 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: H x W x D) 67-7/16" x 28" x 31-5/8". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515504.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth — Cabinet Only “E” = 25 1/4" (64.1 cm).

Why this value was used

Depth — Cabinet Only “E” = 25 1/4" (64.1 cm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — p.28-inch-wide-refrigerator-compatible-with-the-ez-connect-icemaker-kit-18-cu.-ft.wrt518szfg.html
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth Closed Excluding Handles = 31.625 in | city 17.64 cu. ft. Cutout Depth 36.625 in Cutout Width
Reviewed: 2026-09-04

Depth Closed Excluding Handles = 31.625 in | city 17.64 cu. ft. Cutout Depth 36.625 in Cutout Width 28.25 in Depth 31.625 in Depth Closed Excluding Handles 31.625 in Depth Closed Including Handles 31.625 in Depth Excluding Doors 25.25 in Depth W

Why this value was used

Depth Closed Excluding Handles = 31.625 in | city 17.64 cu. ft. Cutout Depth 36.625 in Cutout Width 28.25 in Depth 31.625 in Depth Closed Excluding Handles 31.625 in Depth Closed Including Handles 31.625 in Depth Excluding Doors 25.25 in Depth W

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

H x W x D) 67-7/16" x 28" x 31-5/8"

Why this value was used

H x W x D) 67-7/16" x 28" x 31-5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

57 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth with Door Open 90° 57"

Why this value was used

Depth with Door Open 90° 57"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105515504.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-21

Dimension guide W10843051A: Width - Cabinet "F" = 28 in plus the Location Requirements 1/2 in on each side = 29 in. Owner decision 2026-10-21: replaces Whirlpool web "Cutout Width 28.25 in", narrower than the fridge plus its required side gaps.

Why this value was used

Dimension guide W10843051A: Width - Cabinet "F" = 28 in plus the Location Requirements 1/2 in on each side = 29 in. Owner decision 2026-10-21: replaces Whirlpool web "Cutout Width 28.25 in", narrower than the fridge plus its required side gaps.

Other evidence found

• 28.25 in — superseded

  www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width 28.25 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — 105515504.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Whirlpool opening envelope: max(67.125, 68.25) + 3.0 = 71.25 in.

Why this value was used

Whirlpool opening envelope: max(67.125, 68.25) + 3.0 = 71.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105515504.pdf
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-21

Dimension guide W10843051A: Depth - Cabinet Only "E" = 25 1/4 in plus the required 1 in behind = 26 1/4 in. Owner decision 2026-10-21: replaces Whirlpool web "Cutout Depth 36.625 in".

Why this value was used

Dimension guide W10843051A: Depth - Cabinet Only "E" = 25 1/4 in plus the required 1 in behind = 26 1/4 in. Owner decision 2026-10-21: replaces Whirlpool web "Cutout Depth 36.625 in".

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRT518SZF***

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-W10843051-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern WRT518SZF***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRT518SZF***

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-W10843051-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side Calculation or inference: documented DOE model pattern WRT518SZF***.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Whirlpool measurement source — 105515504.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Conflict adjudication: model-specific dimension guide requires 3 in between overhead cabinets and refrigerator top. Older owner-manual copy stated 1.5 in; the newer/model-specific requirement controls and is more conservative. Evidence: To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on | each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator | top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Why this value was used

Conflict adjudication: model-specific dimension guide requires 3 in between overhead cabinets and refrigerator top. Older owner-manual copy stated 1.5 in; the newer/model-specific requirement controls and is more conservative. Evidence: To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on | each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator | top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515504.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Why this value was used

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105515507.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

H x W x D) 67-7/16" x 28" x 31-5/8"

Why this value was used

H x W x D) 67-7/16" x 28" x 31-5/8"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.