Measurement evidence for Whirlpool WRT104TFDT

Value used by ExactFit

28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

H x W x D) 62-7/8" x 28" x 32-1/4"

Why this value was used

H x W x D) 62-7/8" x 28" x 32-1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

62.3622 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Table Top of Cabinet B: 158.4 cm (62.3622")

Why this value was used

Table Top of Cabinet B: 158.4 cm (62.3622")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

62.874 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Table Overall Height A: 159.7 cm (62.874")

Why this value was used

Table Overall Height A: 159.7 cm (62.874")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Whirlpool WRT104TFDT 28 Inch Top Freezer Refrigerator with 14 cu. ft. Capacity, Adjustable Wire Shelves, Humidity-Controlled Crispers, Dairy Bin, Freezer Temperature Controls, Quiet Cooling, and ADA Compliant: Bisque
www.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth without Door = 25.25 in | Cu. Ft. Total Capacity: 14 Cu. Ft.
Reviewed: 2026-09-04

Exact-model cached specification: Depth without Door = 25.25 in | Cu. Ft. Total Capacity: 14 Cu. Ft. Dimensions Width: 28 Inch Depth: 32 1/4 Inch Depth without Door and Handles: 25 1/4 Inch Depth without Handles: 30 Inch Depth with Door at 90°: 56 3/4 Inch Height: 62

Why this value was used

Exact-model cached specification: Depth without Door = 25.25 in | Cu. Ft. Total Capacity: 14 Cu. Ft. Dimensions Width: 28 Inch Depth: 32 1/4 Inch Depth without Door and Handles: 25 1/4 Inch Depth without Handles: 30 Inch Depth with Door at 90°: 56 3/4 Inch Height: 62

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.2362 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Table Depth Without Handles F: 25.2362"

Why this value was used

Table Depth Without Handles F: 25.2362"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Table Depth With Handles E: 30.0"

Why this value was used

Table Depth With Handles E: 30.0"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

56.7323 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Table Doors Open 90 C: 144.1 cm (56.7323")

Why this value was used

Table Doors Open 90 C: 144.1 cm (56.7323")

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 28.0 + 2 * 0.5

Confidence label: medium.

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 29.0 in from product width 28.0 in and explicit 0.5 in clearance on ea
Reviewed: 2026-09-04

Derived minimum opening width 29.0 in from product width 28.0 in and explicit 0.5 in clearance on each side.

Why this value was used

Derived minimum opening width 29.0 in from product width 28.0 in and explicit 0.5 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 28.0 + 2 * 0.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

63.374 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 62.874 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 62.874 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Whirlpool opening envelope: 25.25 + 1.0 = 26.25 in.

Why this value was used

Whirlpool opening envelope: 25.25 + 1.0 = 26.25 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/201410/dimension-guide-W10679185-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/201410/dimension-guide-W10679185-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" space on each side

Why this value was used

1/2" space on each side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

specialized_exact_printed_model: Allow extra 1/2" on sides and top 1/2"

Why this value was used

specialized_exact_printed_model: Allow extra 1/2" on sides and top 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Why this value was used

Whirlpool installation manual explicit clearance: rear_clearance_in=1 in. To ensure proper ventilation for your refrigerator, allow for a 1/2" (1.25 cm) space on each side. Allow 3" (7.5 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.5 cm) between back of cabinet and the wall. If your

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: conflict-free 2-inch consensus across Whirlpool top-mount installation platforms

Confidence label: medium.

Primary evidence

Whirlpool WRT519SZDT Dimension Guide
assets.skulytics.io · Dimension Guide
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Whirlpool top-mount platform requirement: 2" (5.08 cm) minimum on the hinge side; independently confirmed in WRTX3021, WRTX5028, WRTX5328, and WRTX7421 guides.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

H x W x D) 62-7/8" x 28" x 32-1/4"

Why this value was used

H x W x D) 62-7/8" x 28" x 32-1/4"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool WRT104TFDT Feature Sheet
assets.skulytics.io · Feature Sheet
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

specialized_exact_printed_model: Allow extra 1/2" on sides and top 1/2"

Why this value was used

specialized_exact_printed_model: Allow extra 1/2" on sides and top 1/2"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.