This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-14. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth without Door = 29.625 in | otal Capacity: 28.4 Cu. Ft. Dimensions. Width: 35 1/2 Inch. Depth:
Value used by ExactFit
29.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Whirlpool measurement source — WRSF6536RZ.html www.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Depth without Door = 29.625 in | otal Capacity: 28.4 Cu. Ft. Dimensions. Width: 35 1/2 Inch. Depth: Reviewed: 2026-09-04
Depth without Door = 29.625 in | otal Capacity: 28.4 Cu. Ft. Dimensions. Width: 35 1/2 Inch. Depth: 34 7/8 Inch. Depth without Door: 29 5/8 Inch. Depth without Handles: 32 3/4 Inch. Depth with
Depth without Door = 29.625 in | otal Capacity: 28.4 Cu. Ft. Dimensions. Width: 35 1/2 Inch. Depth: 34 7/8 Inch. Depth without Door: 29 5/8 Inch. Depth without Handles: 32 3/4 Inch. Depth with
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature
range for optimum performance, which reduces electricity
usage and provides superior cooling, is between 60°F (15°C)
and 90°F (32°C). It is recommended that you do not install the
refrigerator near a heat source, such as an oven or radiator.
■Normal minimum cabinet cut-out width required for product -> installation is 36" (91.44 cm). However, if the product is placed
against an extended wall and the ability to remove the crisper
pans is desired, an additional 18" (45.72 cm) of cabinet width is
required, so a total cabinet opening width of 54" (137.16 cm) is
recommended.
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature
range for optimum performance, which reduces electricity
usage and provides superior cooling, is between 60°F (15°C)
and 90°F (32°C). It is recommended that you do not install the
refrigerator near a heat source, such as an oven or radiator.
■Normal minimum cabinet cut-out width required for product -> installation is 36" (91.44 cm). However, if the product is placed
against an extended wall and the ability to remove the crisper
pans is desired, an additional 18" (45.72 cm) of cabinet width is
required, so a total cabinet opening width of 54" (137.16 cm) is
recommended.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest appliance endpoint 69.25 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 29.625 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence
Confidence label: high.
Primary evidence
Whirlpool measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
full-page adjudication=0.5; parser candidates=[0.5, 2.0]; 1.27 cm) of space on each side
full-page adjudication=0.5; parser candidates=[0.5, 2.0]; 1.27 cm) of space on each side
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence
Confidence label: high.
Primary evidence
Whirlpool measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
full-page adjudication=0.5; parser candidates=[0.5, 2.0]; 1.27 cm) of space on each side
full-page adjudication=0.5; parser candidates=[0.5, 2.0]; 1.27 cm) of space on each side
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
1.27 cm) of space on each side and at the top Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-05
2.54 cm) of space behind Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 103455894.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Whirlpool measurement source — 105533907.pdf Publisher not recorded
Page 6
Value used by ExactFit
2 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105533907.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-10-14
2 in printed for Spanish translation says the door opens fully. Read by the verification agent (run De1cda5d602) from a document naming the model.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
2 in printed for Spanish translation says the door opens fully. Read by the verification agent (run De1cda5d602) from a document naming the model.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534043.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Model numbers covered: WRSF6536RZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-14. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
