This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-25. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
69-inch model Height C: 68 1/2 in (174.0 cm), with leveling legs at minimum 1/4-inch extension
69-inch model Height C: 68 1/2 in (174.0 cm), with leveling legs at minimum 1/4-inch extension
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
69-inch model Height A and Height B: 68 7/8 in (174.9 cm), with leveling legs at minimum 1/4-inch extension
69-inch model Height A and Height B: 68 7/8 in (174.9 cm), with leveling legs at minimum 1/4-inch extension
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
Diagram labels 23 7/8 in (60.4 cm) from rear to the front of the cabinet box
Diagram labels 23 7/8 in (60.4 cm) from rear to the front of the cabinet box
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
F Depth with door open 90 degrees: 45 3/4 in (116.21 cm)
Retained specification excerpt: Cutout Width -> 36.5 in
Value used by ExactFit
36.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — response.decoded.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Width -> 36.5 in Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Height -> 70.25 in
Value used by ExactFit
70.25 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — response.decoded.json api.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Height -> 70.25 in Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/truth-set/whirlpool-wrsc6536rz.json", "page": 6, "raw": "Diagram labels 23 7/8 in (60.4 cm) from rear to the front of the cabinet box", "source_url": "https://images.thdstatic.com/catalog/pdfImages/59/59aa4c78-f11e-46f4-99fe-c1c85cf07b22.pdf", "value_in": 23.875}, {"cache_path": "docs/provider-evaluation/raw/skulytics/benchmark-20260811/WRSC6536RZ-5fd2ebb7/specifications/response.decoded.json", "page": "structured exact-SKU response", "raw": "Depth Excluding Doors -> 23.875 in", "source_url": "https://api.skulytics.io/v3/e-commerce/product/specs?matching_rule=exact&page=1&per_page=100&sku=WRSC6536RZ", "value_in": 23.875}], "rear_clearance_in": [{"cache_path": "data/truth-set/whirlpool-wrsc6536rz.json", "page": 5, "raw": "Allow for 1 in (2.54 cm) of space behind the refrigerator", "source_url": "https://images.thdstatic.com/catalog/pdfImages/59/59aa4c78-f11e-46f4-99fe-c1c85cf07b22.pdf", "value_in": 1.0}]}, "result_in": 24.875} Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — owners-manual-w11727207-revA-mirror.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
36 in opening width minus 35 3/4 in product width, divided equally between two sides = 1/8 in each side
36 in opening width minus 35 3/4 in product width, divided equally between two sides = 1/8 in each side
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — owners-manual-w11727207-revA-mirror.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
36 in opening width minus 35 3/4 in product width, divided equally between two sides = 1/8 in each side
36 in opening width minus 35 3/4 in product width, divided equally between two sides = 1/8 in each side
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — owners-manual-w11727207-revA-mirror.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
69 in opening height minus 68 7/8 in minimum overall/hinge height = 1/8 in top clearance
69 in opening height minus 68 7/8 in minimum overall/hinge height = 1/8 in top clearance
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-09
Allow for 1 in (2.54 cm) of space behind the refrigerator
Allow for 1 in (2.54 cm) of space behind the refrigerator
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — owners-manual-w11727207-revA-mirror.pdf Publisher not recorded
Page 5
Value used by ExactFit
2 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — owners-manual-w11727207-revA-mirror.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-10-25
Whirlpool installation instructions: "When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open." Door angle not stated.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Whirlpool installation instructions: "When installing your refrigerator next to a fixed wall, leave a 2" (5.08 cm) minimum space on each side (depending on your model) to allow the doors to swing open." Door angle not stated.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization:
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (fully open). For curved doors at the required minimum 165-degree opening, refrigerator-side Dimension B is 18 3/8 in (46.7 cm)
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (fully open). For curved doors at the required minimum 165-degree opening, refrigerator-side Dimension B is 18 3/8 in (46.7 cm)
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — whirlpool-wrsc6536rz.json images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 6 Reviewed: 2026-09-09
images.thdstatic.com · Web source · secondary model/source
Model numbers covered: WRSC6536RZ. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
11 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout depth; Rear clearance; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-25.
4 displayed measurements supported: Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Wall clearance for door open to 90°.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-25. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
