Measurement evidence for Whirlpool WRS315SDHT

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Cabinet Width E: 35 7/8" (90.11 cm)

Why this value was used

Cabinet Width E: 35 7/8" (90.11 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Height to Top of Cabinet C: 68 5/8" (174.31 cm)

Why this value was used

Height to Top of Cabinet C: 68 5/8" (174.31 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Height D: 69 5/8" (176.85 cm)

Why this value was used

Overall Height D: 69 5/8" (176.85 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Whirlpool measurement source — 522680-whirlpool-wrs315sdht
www.davidselectricinc.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth excluding doors = 28.0 in | (Side-by-Side) from ... Overall Depth 33.63 inch(es) cm Depth (Wit
Reviewed: 2026-09-04

Depth excluding doors = 28.0 in | (Side-by-Side) from ... Overall Depth 33.63 inch(es) cm Depth (Without Handles) Depth excluding doors: 28" • Depth with door Open 90 degree: 49-5/16" • Height to top of cabinet: 68-5/ | cached support: davidselectricinc.com, device.report

Why this value was used

Depth excluding doors = 28.0 in | (Side-by-Side) from ... Overall Depth 33.63 inch(es) cm Depth (Without Handles) Depth excluding doors: 28" • Depth with door Open 90 degree: 49-5/16" • Height to top of cabinet: 68-5/ | cached support: davidselectricinc.com, device.report

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth Without Handles A: 31 5/8" (80.33 cm)

Why this value was used

Depth Without Handles A: 31 5/8" (80.33 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

33.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth With Handles B: 33 5/8" (85.41 cm)

Why this value was used

Depth With Handles B: 33 5/8" (85.41 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49.3125 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Depth with Doors Open 90° F: 49 5/16" (125.25 cm)

Why this value was used

Depth with Doors Open 90° F: 49 5/16" (125.25 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Normal minimum cabinet cutout width: 36" (91.44 cm)

Why this value was used

Normal minimum cabinet cutout width: 36" (91.44 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 69.625 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 69.625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD****

Confidence label: high.

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern WRS315SD****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD****

Confidence label: high.

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" of space on each side

Why this value was used

1/2" of space on each side Calculation or inference: documented DOE model pattern WRS315SD****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD****

Confidence label: high.

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1/2" of space on each side and at the top

Why this value was used

1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern WRS315SD****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRS315SD****

Confidence label: medium.

Primary evidence

Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

1" of space behind

Why this value was used

1" of space behind Calculation or inference: documented DOE model pattern WRS315SD****.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105163299.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 7
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105518731.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Cabinet Width E: 35 7/8" (90.11 cm)

Why this value was used

Cabinet Width E: 35 7/8" (90.11 cm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.