This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Side-by-Side · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.75 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit32.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Cabinet Width E: 32 3/4" (84.12 cm)Open original source ↗ Why this value was usedCabinet Width E: 32 3/4" (84.12 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 65.625 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit65.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Height to Top of Cabinet C: 65 5/8" (166.69 cm)Open original source ↗ Why this value was usedHeight to Top of Cabinet C: 65 5/8" (166.69 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 66.625 in | ✓ Conflicting sources — resolved | Whirlpool measurement source — 105517946.pdf Whirlpool | Page 2 | |
Value used by ExactFit66.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — 105517946.pdf Dimension guide W11105301A (09/17), product dimensions table, row WRS312SNH*: Overall height "D" 66 5/8" (169.23 cm), the top of the hinge cover in the drawing. Replaces the web "Height To Top Of Door Hinge"; the same web page lists the overall height as 66.625 in.Open original source ↗ Why this value was usedDimension guide W11105301A (09/17), product dimensions table, row WRS312SNH*: Overall height "D" 66 5/8" (169.23 cm), the top of the hinge cover in the drawing. Replaces the web "Height To Top Of Door Hinge"; the same web page lists the overall height as 66.625 in. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28 in | ✓ Verified — exact model | Whirlpool measurement source — p.33-inch-wide-side-by-side-refrigerator-22-cu.-ft.wrs312snhm.html Whirlpool | Retained specification excerpt: Depth Excluding Doors: 28.0 in | pth Closed Excluding Handles 31.625 in Depth Closed Including Handl | |
Value used by ExactFit28 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — p.33-inch-wide-side-by-side-refrigerator-22-cu.-ft.wrs312snhm.html Depth Excluding Doors: 28.0 in | pth Closed Excluding Handles 31.625 in Depth Closed Including Handles 33.625 in Depth Excluding Doors 28 in Depth With Door Open 90 Degree 49.313 in Freezer Capacity Volume 7.07 cu. ft. GOpen original source ↗ Why this value was usedDepth Excluding Doors: 28.0 in | pth Closed Excluding Handles 31.625 in Depth Closed Including Handles 33.625 in Depth Excluding Doors 28 in Depth With Door Open 90 Degree 49.313 in Freezer Capacity Volume 7.07 cu. ft. G Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 31.625 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Depth Without Handles A: 31 5/8" (80.33 cm)Open original source ↗ Why this value was usedDepth Without Handles A: 31 5/8" (80.33 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 33.625 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit33.625 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Depth With Handles B: 33 5/8" (85.41 cm)Open original source ↗ Why this value was usedDepth With Handles B: 33 5/8" (85.41 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 49.3125 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit49.3125 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Depth with Doors Open 90° F: 49 5/16" (125.25 cm)Open original source ↗ Why this value was usedDepth with Doors Open 90° F: 49 5/16" (125.25 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Normal minimum cabinet cutout width: 36" (91.44 cm)Open original source ↗ Why this value was usedNormal minimum cabinet cutout width: 36" (91.44 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 67.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Whirlpool measurement source — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit67.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: high. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidenceWhirlpool measurement source — 105517946.pdf Overall height D 66.625 in (guide W11105301A p.2, row WRS312SNH*) plus the printed 1/2 in top clearance (p.1: "allow for 1/2 in of space on each side and at the top") = 67.125 in.Open original source ↗ Why this value was usedOverall height D 66.625 in (guide W11105301A p.2, row WRS312SNH*) plus the printed 1/2 in top clearance (p.1: "allow for 1/2 in of space on each side and at the top") = 67.125 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29 in | ✓ Verified — exact model · Calculated/inferred | Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf Whirlpool | Page 1 | |
Value used by ExactFit29 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidenceWhirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf Minimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in.Open original source ↗ Why this value was usedMinimum opening depth derived from case-only depth 28.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.5 in | ✓ Verified — retained secondary source | Whirlpool measurement source — 105517946.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — 105517946.pdf Allow 1/2 in. of space on each side and at the top.Open original source ↗ Why this value was usedAllow 1/2 in. of space on each side and at the top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.5 in | ✓ Verified — retained secondary source | Whirlpool measurement source — 105517946.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — 105517946.pdf Allow 1/2 in. of space on each side and at the top.Open original source ↗ Why this value was usedAllow 1/2 in. of space on each side and at the top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Whirlpool measurement source — 105517946.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — 105517946.pdf Allow 1/2 in. of space on each side and at the top.Open original source ↗ Why this value was usedAllow 1/2 in. of space on each side and at the top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — exact model · Calculated/inferred | Whirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf Whirlpool | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from WRS311SDHM Confidence label: medium. Primary evidenceWhirlpool measurement source — DimensionGuide-W11105301-D-WH.pdf Conflict-free identical-chassis propagation from Whirlpool WRS311SDHM: rear_clearance_in=1.0 in.Open original source ↗ Why this value was usedConflict-free identical-chassis propagation from Whirlpool WRS311SDHM: rear_clearance_in=1.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from WRS311SDHM. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2 in | ✓ Verified — retained secondary source · Calculated/inferred | Whirlpool measurement source — 105163299.pdf assets.skulytics.io | Page 7 | |
Value used by ExactFit2 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: medium. Primary evidenceWhirlpool measurement source — 105163299.pdf Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cmOpen original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 2" (5.08 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.75 in | ✓ Verified — retained secondary source | Whirlpool installation document — 105517946.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit32.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool installation document — 105517946.pdf Cabinet Width E: 32 3/4" (84.12 cm)Open original source ↗ Why this value was usedCabinet Width E: 32 3/4" (84.12 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 66.625 in. Earlier retained values: 66.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Dimension guide W11105301A (09/17), product dimensions table, row WRS312SNH*: Overall height "D" 66 5/8" (169.23 cm), the top of the hinge cover in the drawing. Replaces the web "Height To Top Of Door Hinge"; the same web page lists the overall height as 66.625 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: WRS312SNHM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Whirlpool · Web source · exact model/source
Model numbers covered: WRS312SNHM. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth without door.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Whirlpool · Web source · exact model/source
Model numbers covered: WRS312SNHM. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout depth; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: WRS312SNHM. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
1 displayed measurements supported: Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.