Measurement evidence for Whirlpool WRR56X18FW

Value used by ExactFit

30.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width - Cabinet = 30-1/4 in.

Why this value was used

Width - Cabinet = 30-1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height - Top of Cabinet = 66-1/4 in.

Why this value was used

Height - Top of Cabinet = 66-1/4 in.

Other evidence found

• 66.2598 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Top of Cabinet B: 168.3 cm (66.2598"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Height - Overall = 66-3/4 in.

Why this value was used

Height - Overall = 66-3/4 in.

Other evidence found

• 66.7323 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Overall Height A: 169.5 cm (66.7323"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Cabinet Only = 24-5/8 in.

Why this value was used

Depth - Cabinet Only = 24-5/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.125 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Without Handles = 29-1/8 in.

Why this value was used

Depth - Without Handles = 29-1/8 in.

Other evidence found

• 24.6063 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Depth Without Handles F: 24.6063". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - With Handles = 30 in.

Why this value was used

Depth - With Handles = 30 in.

Other evidence found

• 29.1339 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Depth With Handles E: 29.1339". The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

55.875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Depth - Door Open 90° = 55-7/8 in.

Why this value was used

Depth - Door Open 90° = 55-7/8 in.

Other evidence found

• 55.8661 in — superseded

  The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Doors Open 90 C: 141.9 cm (55.8661"). The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * side_ventilation_clearance_in

Confidence label: high.

Calculation inputs: Left-side ventilation clearance;

Primary evidence

Whirlpool measurement source — 105520272.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Opening width = product width 30.25 in; Whirlpool requires no side gap for this model (only 1/4" between two appliances side by side).

Why this value was used

Opening width = product width 30.25 in; Whirlpool requires no side gap for this model (only 1/4" between two appliances side by side). Calculation or inference: max(case width, width doors closed) + 2 * side_ventilation_clearance_in.

Other evidence found

• 31.25 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 31.25 in from product width 30.25 in and explicit 0.5 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — 105520272.pdf
assets.skulytics.io · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Whirlpool opening envelope: max(66.25, 66.75) + 0.0 = 66.75 in.

Why this value was used

Whirlpool opening envelope: max(66.25, 66.75) + 0.0 = 66.75 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — 105520283.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.625 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: no manufacturer-specified side minimum in exact-model clearance section

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105520272.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Whirlpool's dimension guide for this model (Ventilation and Clearance) asks only for 1" behind and 1/4" between two appliances installed side by side; unlike its other refrigerator manuals it gives no side-ventilation space, so no side gap is required. The 31 1/4 in cut-out some retailers list is not in Whirlpool's documents or on its product page.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Whirlpool's dimension guide for this model (Ventilation and Clearance) asks only for 1" behind and 1/4" between two appliances installed side by side; unlike its other refrigerator manuals it gives no side-ventilation space, so no side gap is required. The 31 1/4 in cut-out some retailers list is not in Whirlpool's documents or on its product page. Calculation or inference: no manufacturer-specified side minimum in exact-model clearance section.

Other evidence found

• 0.5 in — superseded

  Document Estimate: typical Whirlpool side gap; location not retained. Model scope: not separately recorded. Raw value: Not printed in the Whirlpool documents we have for this model. 1/2 in is the side gap Whirlpool prints for similar models (WRT314TFDW, WRTX5519SZ, WRT104TFDT), so it is shown as an estimate. It is used to work out the opening width, so check the opening against the manual.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: no manufacturer-specified side minimum in exact-model clearance section

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105520272.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-30

Whirlpool's dimension guide for this model (Ventilation and Clearance) asks only for 1" behind and 1/4" between two appliances installed side by side; unlike its other refrigerator manuals it gives no side-ventilation space, so no side gap is required. The 31 1/4 in cut-out some retailers list is not in Whirlpool's documents or on its product page.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Whirlpool's dimension guide for this model (Ventilation and Clearance) asks only for 1" behind and 1/4" between two appliances installed side by side; unlike its other refrigerator manuals it gives no side-ventilation space, so no side gap is required. The 31 1/4 in cut-out some retailers list is not in Whirlpool's documents or on its product page. Calculation or inference: no manufacturer-specified side minimum in exact-model clearance section.

Other evidence found

• 0.5 in — superseded

  Document Estimate: typical Whirlpool side gap; location not retained. Model scope: not separately recorded. Raw value: Not printed in the Whirlpool documents we have for this model. 1/2 in is the side gap Whirlpool prints for similar models (WRT314TFDW, WRTX5519SZ, WRT104TFDT), so it is shown as an estimate. It is used to work out the opening width, so check the opening against the manual.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: no manufacturer-specified top minimum in exact-model clearance section

Confidence label: medium.

Primary evidence

Whirlpool specification record — 105520272.pdf
assets.skulytics.io · Specification sheet
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

The model-specific clearance section specifies 1" rear and 1/4" between paired appliances; it specifies no minimum above.

Why this value was used

The model-specific clearance section specifies 1" rear and 1/4" between paired appliances; it specifies no minimum above. Calculation or inference: no manufacturer-specified top minimum in exact-model clearance section.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document

Confidence label: medium.

Primary evidence

Whirlpool measurement source — 105520283.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 5
Reviewed: 2026-09-05

2.54 cm) space behind

Why this value was used

2.54 cm) space behind Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30.25 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105520272.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

Width - Cabinet = 30-1/4 in.

Why this value was used

Width - Cabinet = 30-1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.