Measurement evidence for Whirlpool WRMF3736SZ

Value used by ExactFit

35.9375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 240744WRG01-160_WRMF3736SZ_CAD.zip
www.harpersappliances.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model official manufacturer CAD OBJ bounding-box x-extent = 35.909016 in; visually checked ori
Reviewed: 2026-09-11

Exact-model official manufacturer CAD OBJ bounding-box x-extent = 35.909016 in; visually checked orientation/state and corroborates the retained published value 35.9375 in within the declared 1/8 in CAD-geometry tolerance. Raw geometric precision is not published.

Why this value was used

Exact-model official manufacturer CAD OBJ bounding-box x-extent = 35.909016 in; visually checked orientation/state and corroborates the retained published value 35.9375 in within the declared 1/8 in CAD-geometry tolerance. Raw geometric precision is not published.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

69 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105603201.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

C* Height to top of cabinet -> 69" (1753 mm)

Why this value was used

C* Height to top of cabinet -> 69" (1753 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 240744WRG01-160_WRMF3736SZ_CAD.zip
www.homedepot.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model official manufacturer CAD OBJ bounding-box z-extent = 70.063906 in; visually checked ori
Reviewed: 2026-09-11

Exact-model official manufacturer CAD OBJ bounding-box z-extent = 70.063906 in; visually checked orientation/state and corroborates the retained published value 70.0625 in within the declared 1/8 in CAD-geometry tolerance. Raw geometric precision is not published.

Why this value was used

Exact-model official manufacturer CAD OBJ bounding-box z-extent = 70.063906 in; visually checked orientation/state and corroborates the retained published value 70.0625 in within the declared 1/8 in CAD-geometry tolerance. Raw geometric precision is not published.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105603201.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

F Depth without doors -> 297/8" (758.8 mm)

Why this value was used

F Depth without doors -> 297/8" (758.8 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105603201.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

E Depth with doors -> 34 3/4" (882.3 mm)

Why this value was used

E Depth with doors -> 34 3/4" (882.3 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — whirlpool-french-door-step-up-amp-spec-guide
learnwhirlpool.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Manufacturer lineup guide and exact-model saved answer agree: Depth Including Handles 34 3/4 in.
Reviewed: 2026-09-04

Manufacturer lineup guide and exact-model saved answer agree: Depth Including Handles 34 3/4 in.

Why this value was used

Manufacturer lineup guide and exact-model saved answer agree: Depth Including Handles 34 3/4 in.

Other evidence found

• 90 in — superseded

  www.townappliance.com; location not retained. Model scope: not separately recorded. Raw value: **product depth** : **Depth With Door Open 90 Degree** . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 90 in — superseded

  www.townappliance.com; location not retained. Model scope: not separately recorded. Raw value: **product depth** : **Depth With Door Open 90 Degree** . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

49 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool installation document — 105603201.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-04

K Depth with doors open 90° -> 49" (1245.2 mm)

Why this value was used

K Depth with doors open 90° -> 49" (1245.2 mm)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.9375 + 2 * 0.5

Confidence label: medium.

Primary evidence

Whirlpool measurement source — MODEL?KEY=WHIRL%3AWRMF3736SZ + 105603201.pdf
www.harpersappliances.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.9375 + 2 * 0.5 = 36.9375 in. Side evidence: Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.9375 + 2 * 0.5 = 36.9375 in. Side evidence: Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top. Calculation or inference: 35.9375 + 2 * 0.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Whirlpool measurement source — dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in.

Why this value was used

Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Whirlpool measurement source — dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105603201.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105603201.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Why this value was used

Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SV, WRMF3536SZ, WRMF3536SW. Exact byte-identical PDF (SHA-256 4154c0cc02a6c038ae3a4a84080b9fb3746c59d9775e4eef83afc2126c4f7615) shared with variant(s) WRMF3536SW. To ensure proper ventilation, allow for a 1/2" (12.5 mm) space on each side and at the top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from WRMF3536SZ

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Whirlpool WRMF3536SZ: top_clearance_in=0.5 in.

Why this value was used

Conflict-free identical-chassis propagation from Whirlpool WRMF3536SZ: top_clearance_in=0.5 in. Calculation or inference: identical 8-dimension chassis signature; propagated from WRMF3536SZ.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from WRMF3536SZ

Confidence label: medium.

Primary evidence

Whirlpool measurement source — dimension-guide-w11783872-reva.pdf
Whirlpool · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Whirlpool WRMF3536SZ: rear_clearance_in=2.0 in.

Why this value was used

Conflict-free identical-chassis propagation from Whirlpool WRMF3536SZ: rear_clearance_in=2.0 in. Calculation or inference: identical 8-dimension chassis signature; propagated from WRMF3536SZ.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105603201.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). When installing next to a fixed wall, leave a minimum space of 3.75" (95 mm) between the refrigerator and wall.

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). When installing next to a fixed wall, leave a minimum space of 3.75" (95 mm) between the refrigerator and wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

14 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 105603024.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-14

14 in printed for full door swing at 135 degrees. Read by the verification agent (run D4154c0cc02) from a document naming the model.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

14 in printed for full door swing at 135 degrees. Read by the verification agent (run D4154c0cc02) from a document naming the model.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.9375 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Whirlpool measurement source — 240744WRG01-160_WRMF3736SZ_CAD.zip
www.ajmadison.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-22

Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).

Why this value was used

Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).

Other evidence found

• 35.8125 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Whirlpool WRMF3736SW cached finish-variant chassis match. The final reviewed registry supersedes this earlier audit value.

• 35.8125 in — superseded

  www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model official manufacturer CAD OBJ bounding-box x-extent = 35.909016 in; visually checked orientation/state and corroborates the retained published value 35.8125 in within the declared 1/8 in CAD-geometry tolerance. Raw geometric precision is not published.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.