This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-22. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 240744WRG02-028_WRMF3636SZ_CAD.zip Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Other evidence found
35.94 in — superseded
www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: net Width: 35.94 in | Drawers 1 Full Width ### Electrical Amps 20 Hz 60 Volts 115 ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36. The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height To Top Of Cabinet = 69.0 in | in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 370 lbs H
Value used by ExactFit
69 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — p.whirlpool-29-cu.-ft.-family-sized-capacity-french-door-refrigerator-with-flexible-temperature-drawer.wrmf3636sz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Height To Top Of Cabinet = 69.0 in | in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 370 lbs H Reviewed: 2026-09-04
Height To Top Of Cabinet = 69.0 in | in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 370 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height
Height To Top Of Cabinet = 69.0 in | in Freezer Capacity Volume 9.01 cu. ft. Gross Weight 370 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105602904.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22
Dimension guide W11783874A (WRMF3636S*), table: D Height of top of hinges 70 1/16" (1779.5 mm).
Dimension guide W11783874A (WRMF3636S*), table: D Height of top of hinges 70 1/16" (1779.5 mm).
Other evidence found
70.06 in — superseded
www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Height To Top Of Door Hinge: 70.06 in | 1 cu. ft. Gross Weight 370 lbs Height 70.0625 in Height To Top Of Cabinet 69 in Height To Top Of Door Hinge 70.063 in Maximum Height 70.0625 in Minimum Height 69 in Net Weight 339 lbs Refrigerator . The final reviewed registry supersedes this earlier audit value.
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105602904.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105602904.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
www.shopappliances.com; location not retained. Model scope: not separately recorded. Raw value: depth without handles : Depth with Door Opened at 90 Degrees . The final reviewed registry supersedes this earlier audit value.
Retained specification excerpt: Depth Closed Including Handles: 36.81 in | Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excl
Value used by ExactFit
36.81 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — p.whirlpool-29-cu.-ft.-family-sized-capacity-french-door-refrigerator-with-flexible-temperature-drawer.wrmf3636sz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Closed Including Handles: 36.81 in | Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excl Reviewed: 2026-09-04
Depth Closed Including Handles: 36.81 in | Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Depth Closed Including Handles: 36.81 in | Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Other evidence found
90 in — superseded
www.absoluteappliances.com; location not retained. Model scope: not separately recorded. Raw value: product depth : Depth With Door Open 90 Degree . The final reviewed registry supersedes this earlier audit value.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105602904.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
36.9375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: width 35.9375 + 2 x 0.5
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 105602904.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-22
Cutout width = width 35 15/16 in + 1/2 in on each side (guide p.2: allow 1/2" space on each side and at the top). Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Cutout width = width 35 15/16 in + 1/2 in on each side (guide p.2: allow 1/2" space on each side and at the top). Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md). Calculation or inference: width 35.9375 + 2 x 0.5.
Other evidence found
36.19 in — superseded
www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Cutout Width: 36.19 in | Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including. The final reviewed registry supersedes this earlier audit value.
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — 105602904.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-22
Dimension guide W11783874A (WRMF3636S*): D Height of top of hinges 70 1/16" (p.1) plus the printed 1/2" top space (p.2) = 70 9/16 in.
Dimension guide W11783874A (WRMF3636S*): D Height of top of hinges 70 1/16" (p.1) plus the printed 1/2" top space (p.2) = 70 9/16 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3636SZ
Confidence label: high.
Primary evidence
Whirlpool measurement source — dimension-guide-w11783874-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRMF3636SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3636SZ
Confidence label: high.
Primary evidence
Whirlpool measurement source — dimension-guide-w11783874-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRMF3636SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3636SZ
Confidence label: high.
Primary evidence
Whirlpool measurement source — dimension-guide-w11783874-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side and at the top Calculation or inference: documented DOE model pattern WRMF3636SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMF3636SZ
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11783874-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
2" space behind Calculation or inference: documented DOE model pattern WRMF3636SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — 105602904.pdf Publisher not recorded
Page 2
Value used by ExactFit
3.75 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105602904.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-22
Dimension guide W11783874A (WRMF3636S*), Location Requirements: "When installing your refrigerator next to a fixed wall, leave a minimum space of 3.75" (95 mm) between the refrigerator and the wall to allow the door to swing open."
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
Dimension guide W11783874A (WRMF3636S*), Location Requirements: "When installing your refrigerator next to a fixed wall, leave a minimum space of 3.75" (95 mm) between the refrigerator and the wall to allow the door to swing open."
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Whirlpool measurement source — 105602838.pdf Publisher not recorded
Page 2
Value used by ExactFit
14 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105602838.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-14
14 in printed for full door swing at 135 degrees. Read by the verification agent (run Df243dcb7c9) from a document naming the model.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
14 in printed for full door swing at 135 degrees. Read by the verification agent (run Df243dcb7c9) from a document naming the model.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 240744WRG02-028_WRMF3636SZ_CAD.zip Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-10-22
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Other evidence found
35.94 in — superseded
www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Cabinet Width: 35.94 in | lled Drawers 1 Full Width ### Electrical Amps 20 Hz 60 Volts 115 ### Dimensions Cabinet Width 35.938 in Capacity 28.9 cu. ft. Common Size 36 in Cutout Height 70.188 in Cutout Width 36. The final reviewed registry supersedes this earlier audit value.
Selected: 35.9375 in. Earlier retained values: 35.94 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Selected: 36.81 in. Earlier retained values: 90 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Depth Closed Including Handles: 36.81 in | Cutout Width 36.188 in Depth 36.8125 in Depth Closed Excluding Handles 34.75 in Depth Closed Including Handles 36.813 in Depth Excluding Doors 29.875 in Depth With Door Open 90 Degree 49 in Freezer Ca
Selected: 36.9375 in. Earlier retained values: 36.19 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cutout width = width 35 15/16 in + 1/2 in on each side (guide p.2: allow 1/2" space on each side and at the top). Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md). Calculation or inference: width 35.9375 + 2 x 0.5.
Selected: 35.9375 in. Earlier retained values: 35.94 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Width 35 15/16 in: the Whirlpool spec sheet prints Cabinet Width 35.938 and Width 35.9375, and the Whirlpool 3D CAD models of this chassis measure 35.91 in wide; the dimension guide's 35 13/16 (909 mm) matches the KitchenAid version instead. Owner decision 2026-10-22 (variant-families-review-2026-10-22.owner-decisions.md).
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
7 displayed measurements supported: Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Wall clearance for door open to 90°.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
