This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Four-door French door · Counter-depth
Market status: Reviewed (recorded 2026-08-17)
Last reviewed: 2026-10-15. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ? Verified — finalized database measurement | Whirlpool measurement source — whirlpool-wrmc7036rz.json assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json D Width of cabinet: 35 5/8 in (90.5 cm)Open original source ↗ All retained supporting links
Why this value was usedD Width of cabinet: 35 5/8 in (90.5 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 68.875 in | ? Verified — finalized database measurement | Whirlpool measurement source — whirlpool-wrmc7036rz.json assets.skulytics.io | Page 1 | |
Value used by ExactFit68.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json B Height to top of cabinet: 68 7/8 in (175 cm)Open original source ↗ All retained supporting links
Why this value was usedB Height to top of cabinet: 68 7/8 in (175 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 69.9375 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 1 | |
Value used by ExactFit69.9375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json C Overall Height: 69 15/16 in (177.6 cm); dimension includes rollers extended 3/4 inOpen original source ↗ Why this value was usedC Overall Height: 69 15/16 in (177.6 cm); dimension includes rollers extended 3/4 in Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25 in | ? Verified — finalized database measurement | Whirlpool measurement source — whirlpool-wrmc7036rz.json assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json F Depth without doors: 25 in (63.5 cm)Open original source ↗ All retained supporting links
Why this value was usedF Depth without doors: 25 in (63.5 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 29.4375 in | ? Verified — finalized database measurement | Whirlpool measurement source — whirlpool-wrmc7036rz.json assets.skulytics.io | Page 1 | |
Value used by ExactFit29.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json A Depth without handles: 29 7/16 in (74.85 cm)Open original source ↗ All retained supporting links
Why this value was usedA Depth without handles: 29 7/16 in (74.85 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 29.4375 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Retained specification excerpt: Official page publishes 29.4375-in total depth; the model uses non-projecting pocket handles | |
Value used by ExactFit29.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Official page publishes 29.4375-in total depth; the model uses non-projecting pocket handlesOpen original source ↗ Why this value was usedOfficial page publishes 29.4375-in total depth; the model uses non-projecting pocket handles Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 44.25 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 1 | |
Value used by ExactFit44.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Dimension E is drawn front-to-back with both doors at 90 degrees and equals 44 1/4 in (112.4 cm)Open original source ↗ Why this value was usedDimension E is drawn front-to-back with both doors at 90 degrees and equals 44 1/4 in (112.4 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Opening Width A: 36 in (91.46 cm)Open original source ↗ Why this value was usedOpening Width A: 36 in (91.46 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 70.1875 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit70.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Opening Height B: 70 3/16 in (178.24 cm)Open original source ↗ Why this value was usedOpening Height B: 70 3/16 in (178.24 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 26 in | ✓ Conflicting sources — resolved | Whirlpool measurement source — web-b7bb1b2813.pdf Whirlpool | Page 2 | |
Value used by ExactFit26 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — web-b7bb1b2813.pdf Dimension guide W11778227 rev B (2026-08), Location Requirements: "Depth (C) 26" (66 cm)". Supersedes rev A (W11778226A) and the owner manual, which printed 30 1/2".Open original source ↗ Why this value was usedDimension guide W11778227 rev B (2026-08), Location Requirements: "Depth (C) 26" (66 cm)". Supersedes rev A (W11778226A) and the owner manual, which printed 30 1/2". Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.1875 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Allow 3/16 in (0.48 cm) on each sideOpen original source ↗ Why this value was usedAllow 3/16 in (0.48 cm) on each side Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.1875 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit0.1875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Allow 3/16 in (0.48 cm) on each sideOpen original source ↗ Why this value was usedAllow 3/16 in (0.48 cm) on each side Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.25 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Allow 1/4 in (0.64 cm) at the topOpen original source ↗ Why this value was usedAllow 1/4 in (0.64 cm) at the top Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Allow 1 in (2.54 cm) behind the refrigeratorOpen original source ↗ Why this value was usedAllow 1 in (2.54 cm) behind the refrigerator Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 3.75 in | ✓ Verified — exact model | Whirlpool measurement source — whirlpool-wrmc7036rz.json Whirlpool | Page 2 | |
Value used by ExactFit3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Next to a fixed wall, leave 3 3/4 in (9.5 cm) minimum between refrigerator and wall to allow the door to swing openOpen original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Next to a fixed wall, leave 3 3/4 in (9.5 cm) minimum between refrigerator and wall to allow the door to swing open Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ? Verified — finalized database measurement | Whirlpool measurement source — whirlpool-wrmc7036rz.json assets.skulytics.io | Page 1 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceWhirlpool measurement source — whirlpool-wrmc7036rz.json D Width of cabinet: 35 5/8 in (90.5 cm)Open original source ↗ All retained supporting links
Why this value was usedD Width of cabinet: 35 5/8 in (90.5 cm) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 26 in. Earlier retained values: 30.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Dimension guide W11778227 rev B (2026-08), Location Requirements: "Depth (C) 26" (66 cm)". Supersedes rev A (W11778226A) and the owner manual, which printed 30 1/2".
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Web source · Scope not established
Model numbers covered: WRMC7036RV. Publication/revision date: Not recorded. Reviewed: 2026-09-09.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Whirlpool · Web source · exact model/source
Model numbers covered: WRMC7036RZ. Publication/revision date: Not recorded. Reviewed: 2026-10-15.
1 displayed measurements supported: Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-15. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.