This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-22. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105603435.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105603435.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u.
Value used by ExactFit
69.88 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — p.36-inch-wide-true-counter-depth-4-door-french-door-refrigerator-22-cu.-ft.wrmc5036rz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u. Reviewed: 2026-09-04
Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u. ft. Gross Weight 365 lbs Height 69.875 in Height To Top Of Cabinet 68.875 in Height To Top Of Door Hinge 69.875 in Maximum Height 69.875 in Minimum Height 68.875 in Net Weight 350 lbs Refrigerat
Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u. ft. Gross Weight 365 lbs Height 69.875 in Height To Top Of Cabinet 68.875 in Height To Top Of Door Hinge 69.875 in Maximum Height 69.875 in Minimum Height 68.875 in Net Weight 350 lbs Refrigerat
Other evidence found
69.9375 in — superseded
Document 105603435.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height
6915/16" (177.6 cm). The final reviewed registry supersedes this earlier audit value.
69.3125 in — superseded
Document 105603435.pdf; page 1. Model scope: not separately recorded. Raw value: Overall height = 69-5/16 in.. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105603435.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105603435.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Retained specification excerpt: Rounding normalised 2026-10-22: the stored 29.44 in is the same printed dimension as 29 7/16 in (29.
Value used by ExactFit
29.4375 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — p.36-inch-wide-true-counter-depth-4-door-french-door-refrigerator-22-cu.-ft.wrmc5036rz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Rounding normalised 2026-10-22: the stored 29.44 in is the same printed dimension as 29 7/16 in (29. Reviewed: 2026-10-22
Rounding normalised 2026-10-22: the stored 29.44 in is the same printed dimension as 29 7/16 in (29.4375); every finish of the WRMC5036R family carries the same value to within 0.02 in. Source kept as stored.
Rounding normalised 2026-10-22: the stored 29.44 in is the same printed dimension as 29 7/16 in (29.4375); every finish of the WRMC5036R family carries the same value to within 0.02 in. Source kept as stored.
Other evidence found
29.44 in — superseded
The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Depth Closed Including Handles: 29.44 in | tout Height 70.125 in Depth 31.4375 in Depth Closed Excluding Handles 29.438 in Depth Closed Including Handles 29.438 in Depth Excluding Doors 25 in Depth With Door Open 90 Degree 44.25 in Freezer Cap. The final reviewed registry supersedes this earlier audit value.
Retained specification excerpt: Depth Excluding Doors 25 in Depth With Door Open 90: 44.25 in | pth Closed Excluding Handles 29.438
Value used by ExactFit
44.25 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — p.36-inch-wide-true-counter-depth-4-door-french-door-refrigerator-22-cu.-ft.wrmc5036rz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Excluding Doors 25 in Depth With Door Open 90: 44.25 in | pth Closed Excluding Handles 29.438 Reviewed: 2026-09-04
Depth Excluding Doors 25 in Depth With Door Open 90: 44.25 in | pth Closed Excluding Handles 29.438 in Depth Closed Including Handles 29.438 in Depth Excluding Doors 25 in Depth With Door Open 90 Degree 44.25 in Freezer Capacity Volume 6.57 cu. ft. Gross Weight 365 lbs Height 69.875 in Heig
Depth Excluding Doors 25 in Depth With Door Open 90: 44.25 in | pth Closed Excluding Handles 29.438 in Depth Closed Including Handles 29.438 in Depth Excluding Doors 25 in Depth With Door Open 90 Degree 44.25 in Freezer Capacity Volume 6.57 cu. ft. Gross Weight 365 lbs Height 69.875 in Heig
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
36 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 35.625 + 2 * 0.1875
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 105603435.pdf + 105603435.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-04
Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.625 + 2 * 0.1875 = 36.0 in. Side evidence: allow for 3/16" (0.48 cm) space on each side
Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.625 + 2 * 0.1875 = 36.0 in. Side evidence: allow for 3/16" (0.48 cm) space on each side Calculation or inference: 35.625 + 2 * 0.1875.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 69.88 in plus documented top clearance 0.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMC5036R***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11778224-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side Calculation or inference: documented DOE model pattern WRMC5036R***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMC5036R***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11778224-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side Calculation or inference: documented DOE model pattern WRMC5036R***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMC5036R***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11778224-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
3/16" space on each side and 1/4" space at the top
3/16" space on each side and 1/4" space at the top Calculation or inference: documented DOE model pattern WRMC5036R***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRMC5036R***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11778224-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1" space behind Calculation or inference: documented DOE model pattern WRMC5036R***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 105603409.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33/4" (9.5 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33/4" (9.5 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105603435.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Selected: 69.88 in. Earlier retained values: 69.9375 in, 69.3125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u. ft. Gross Weight 365 lbs Height 69.875 in Height To Top Of Cabinet 68.875 in Height To Top Of Door Hinge 69.875 in Maximum Height 69.875 in Minimum Height 68.875 in Net Weight 350 lbs Refrigerat
Selected: 29.4375 in. Earlier retained values: 29.44 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Rounding normalised 2026-10-22: the stored 29.44 in is the same printed dimension as 29 7/16 in (29.4375); every finish of the WRMC5036R family carries the same value to within 0.02 in. Source kept as stored.
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
