This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-04. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Whirlpool measurement source — 105534739.pdf + side gap from the maker's document assets.skulytics.io
Retained specification excerpt: Derived minimum opening width 36.8125 in from product width 35.8125 in and explicit 0.5 in clearance
Value used by ExactFit
36.8125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.8125 + 2 * 0.5
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 105534739.pdf + side gap from the maker's document assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Derived minimum opening width 36.8125 in from product width 35.8125 in and explicit 0.5 in clearance Reviewed: 2026-09-04
Derived minimum opening width 36.8125 in from product width 35.8125 in and explicit 0.5 in clearance on each side.
Derived minimum opening width 36.8125 in from product width 35.8125 in and explicit 0.5 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.8125 + 2 * 0.5.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening height derived from highest stored appliance endpoint 70.0625 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Minimum opening depth derived from case-only depth 29.875 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFF3136SZ
Confidence label: high.
Primary evidence
Whirlpool measurement source — dimension-guide-w11642947-revb.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRFF3136SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFF3136SZ
Confidence label: high.
Primary evidence
Whirlpool measurement source — dimension-guide-w11642947-revb.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRFF3136SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFF3136SZ
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11642947-revb.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side and at the top Calculation or inference: documented DOE model pattern WRFF3136SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFF3136SZ
Confidence label: medium.
Primary evidence
Whirlpool measurement source — dimension-guide-w11642947-revb.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
2" space behind Calculation or inference: documented DOE model pattern WRFF3136SZ.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document
Confidence label: medium.
Primary evidence
Whirlpool measurement source — 106162611.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 7 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 3 3/4" (9.5 cm
Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 3 3/4" (9.5 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Whirlpool measurement source — 105534739.pdf Publisher not recorded
Page 2
Value used by ExactFit
14 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105534739.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-10-04
"To allow for a full door swing, you will need to leave 14" (355 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
"To allow for a full door swing, you will need to leave 14" (355 mm) of space between the refrigerator and the wall"; the drawing shows the door fully open at 135 degrees.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool installation document — 105534739.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04
Model numbers covered: WRFF3136SZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
9 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-10-04. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
