Measurement evidence for Whirlpool WRFC7036RZ

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Whirlpool WRFC7036RZ fit check Check this model against your opening How ExactFit verifies measurements

Whirlpool WRFC7036RZ

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

6exact-model manufacturer values

0verified equivalent/same-chassis values

9secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-09-17. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.625 in	✓ Verified — retained secondary source	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Aligned with case_width_in (35.625") Open original source ↗ Why this value was used Aligned with case_width_in (35.625") Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.875 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 68.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Exact-model dimension sheet: Height to top of cabinet = 68 7/8 in. Open original source ↗ Why this value was used Exact-model dimension sheet: Height to top of cabinet = 68 7/8 in. Other evidence found 68.75 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Height to top of cabinet = 68-7/8 in.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	69.875 in	✓ Conflicting sources — resolved	Whirlpool measurement source — exact-model specification: Height To Top Of Door Hinge = 69.875 in Whirlpool	Retained specification excerpt: Exact-model manufacturer specification: Height To Top Of Door Hinge = 69.875 in.
Value used by ExactFit 69.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool measurement source — exact-model specification: Height To Top Of Door Hinge = 69.875 in Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Exact-model manufacturer specification: Height To Top Of Door Hinge = 69.875 in. Reviewed: 2026-09-04 Exact-model manufacturer specification: Height To Top Of Door Hinge = 69.875 in. Open original source ↗ Why this value was used Exact-model manufacturer specification: Height To Top Of Door Hinge = 69.875 in. Other evidence found 69.9375 in — superseded Document 105603386.pdf; page 1. Model scope: not separately recorded. Raw value: Overall Height 6915/16" (177.6 cm). The final reviewed registry supersedes this earlier audit value. 69.3125 in — superseded Document 105603386.pdf; page 1. Model scope: not separately recorded. Raw value: Overall height = 69-5/16 in.. The final reviewed registry supersedes this earlier audit value. 69.88 in — superseded www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed cached exact-model manufacturer label: Height To Top Of Door Hinge = 69.88 in. Context: u. ft. Gross Weight 360 lbs Height 69.875 in Height To Top Of Cabinet 68.875 in Height To Top Of Door Hinge 69.875 in Maximum Height 69.875 in Minimum Height 68.875 in Net Weight 345 lbs Refrigerat. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	25 in	✓ Verified — retained secondary source	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth without doors 25" (63.5 cm) Open original source ↗ Why this value was used Depth without doors 25" (63.5 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	29.4375 in	✓ Verified — retained secondary source	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 29.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth without handles 297/16" (74.85 cm) Open original source ↗ Why this value was used Depth without handles 297/16" (74.85 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	31.4375 in	✓ Verified — retained secondary source	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 31.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth with handles 317/16" (79.95 cm) Open original source ↗ Why this value was used Depth with handles 317/16" (79.95 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	44.25 in	✓ Verified — exact model	Whirlpool measurement source — p.36-inch-wide-true-counter-depth-3-door-french-door-refrigerator-23.4-cu.-ft.wrfc7036rz.html Whirlpool	Retained specification excerpt: Depth With Door Open 90: 44.25 in \| l 36-inch Wide True Counter Depth 3-Door French Door Refrigerato
Value used by ExactFit 44.25 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool measurement source — p.36-inch-wide-true-counter-depth-3-door-french-door-refrigerator-23.4-cu.-ft.wrfc7036rz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90: 44.25 in \| l 36-inch Wide True Counter Depth 3-Door French Door Refrigerato Reviewed: 2026-09-04 Depth With Door Open 90: 44.25 in \| l 36-inch Wide True Counter Depth 3-Door French Door Refrigerator - 23.4 cu ... Depth With Door Open 90 Degree. 44.25 in. Freezer Capacity Volume. Open original source ↗ Why this value was used Depth With Door Open 90: 44.25 in \| l 36-inch Wide True Counter Depth 3-Door French Door Refrigerator - 23.4 cu ... Depth With Door Open 90 Degree. 44.25 in. Freezer Capacity Volume. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36 in	✓ Verified — exact model	Whirlpool measurement source — p.36-inch-wide-true-counter-depth-3-door-french-door-refrigerator-23.4-cu.-ft.wrfc7036rz.html Whirlpool	Retained specification excerpt: Cutout Width: 36.0 in \| Width 35.625 in Capacity 23.4 cu. ft. Common Size 36 in Cutout Height 70.125
Value used by ExactFit 36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool measurement source — p.36-inch-wide-true-counter-depth-3-door-french-door-refrigerator-23.4-cu.-ft.wrfc7036rz.html Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Width: 36.0 in \| Width 35.625 in Capacity 23.4 cu. ft. Common Size 36 in Cutout Height 70.125 Reviewed: 2026-09-04 Cutout Width: 36.0 in \| Width 35.625 in Capacity 23.4 cu. ft. Common Size 36 in Cutout Height 70.125 in Cutout Width 36 in Depth 31.4375 in Depth Closed Excluding Handles 29.438 in Depth Closed Includin Open original source ↗ Why this value was used Cutout Width: 36.0 in \| Width 35.625 in Capacity 23.4 cu. ft. Common Size 36 in Cutout Height 70.125 in Cutout Width 36 in Depth 31.4375 in Depth Closed Excluding Handles 29.438 in Depth Closed Includin Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.125 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 70.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Minimum opening height derived from highest stored appliance endpoint 69.875 in plus documented top clearance 0.25 in. Open original source ↗ Why this value was used Minimum opening height derived from highest stored appliance endpoint 69.875 in plus documented top clearance 0.25 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	26 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Open original source ↗ Why this value was used Minimum opening depth derived from case-only depth 25.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.1875 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC7036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 3/16" space on each side Open original source ↗ Why this value was used 3/16" space on each side Calculation or inference: documented DOE model pattern WRFC7036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.1875 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 0.1875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC7036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 3/16" space on each side Open original source ↗ Why this value was used 3/16" space on each side Calculation or inference: documented DOE model pattern WRFC7036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.25 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC7036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 3/16" space on each side and 1/4" space at the top Open original source ↗ Why this value was used 3/16" space on each side and 1/4" space at the top Calculation or inference: documented DOE model pattern WRFC7036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool	Page 2
Value used by ExactFit 1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC7036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11778228-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05 1" space behind Open original source ↗ Why this value was used 1" space behind Calculation or inference: documented DOE model pattern WRFC7036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	3.75 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — 105603360.pdf assets.skulytics.io	Page 2
Value used by ExactFit 3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: medium. Primary evidence Whirlpool measurement source — 105603360.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33/4" (9.5 cm Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33/4" (9.5 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.625 in	✓ Verified — retained secondary source	Whirlpool installation document — 105603386.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105603386.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width of cabinet 355/8" (90.5 cm) Open original source ↗ Why this value was used Width of cabinet 355/8" (90.5 cm) Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 68.875 in. Earlier retained values: 68.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact-model dimension sheet: Height to top of cabinet = 68 7/8 in.

View source scope, location, and impact on fit

Height with hinge / controlling height

Selected: 69.875 in. Earlier retained values: 69.9375 in, 69.3125 in, 69.88 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Exact-model manufacturer specification: Height To Top Of Door Hinge = 69.875 in.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Whirlpool installation document — 105603386.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: WRFC7036RZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

6 displayed measurements supported: Overall width; Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Cabinet case width.