Measurement evidence for Whirlpool WRFC2036RZ

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Whirlpool WRFC2036RZ fit check Check this model against your opening How ExactFit verifies measurements

Whirlpool WRFC2036RZ

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

4exact-model manufacturer values

0verified equivalent/same-chassis values

11secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-09-28. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.625 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width - Cabinet = 35-5/8 in. Open original source ↗ Why this value was used Width - Cabinet = 35-5/8 in. Other evidence found 45.3937 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Width Cabinet H: 45.3937". The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.875 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 68.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height - Top of Cabinet = 68-7/8 in. Open original source ↗ Why this value was used Height - Top of Cabinet = 68-7/8 in. Other evidence found 70.1181 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Top of Cabinet B: 178.1 cm (70.1181"). The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	70.125 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 70.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Height - Overall = 70-1/8 in. Open original source ↗ Why this value was used Height - Overall = 70-1/8 in. Other evidence found 70.1181 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Overall Height A: 178.1 cm (70.1181"). The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24.25 in	✓ Verified — retained secondary source	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 24.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth - Cabinet Only = 24-1/4 in. Open original source ↗ Why this value was used Depth - Cabinet Only = 24-1/4 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	26.875 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 26.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth - Without Handles = 26-7/8 in. Open original source ↗ Why this value was used Depth - Without Handles = 26-7/8 in. Other evidence found 42.9921 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Depth Without Handles F: 42.9921". The final reviewed registry supersedes this earlier audit value. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	30.5 in	✓ Conflicting sources — resolved	Whirlpool measurement source — 105533290.pdf Whirlpool	Page 1
Value used by ExactFit 30.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool measurement source — 105533290.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-28 Doors closed, handles included: 30 1/2 in; the sheet prints 26 7/8 in without handles and names WRFC2036R. Open original source ↗ Why this value was used Doors closed, handles included: 30 1/2 in; the sheet prints 26 7/8 in without handles and names WRFC2036R. Other evidence found 48.1102 in — superseded Document 105533202.pdf; page 1. Model scope: not separately recorded. Raw value: Table Depth With Handles E: 48.1102". The final reviewed registry supersedes this earlier audit value. 29.38 in — superseded www.whirlpool.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed cached exact-model manufacturer label: Depth Closed Including Handles = 29.38 in. Context: in Capacity 20 cu. ft. Depth 29.375 in Depth Closed Excluding Handles 26.875 in Depth Closed Including Handles 29.375 in Depth Excluding Doors 24.125 in Freezer Capacity Volume 5.62 cu. ft. Gross Weig. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	43 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 43 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Depth - Doors Open 90° = 43 in. Open original source ↗ Why this value was used Depth - Doors Open 90° = 43 in. Other evidence found 68.8583 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Doors Open 90 C: 174.9 cm (68.8583"). The final reviewed registry supersedes this earlier audit value. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36.625 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — 105533202.pdf + 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 35.625 + 2 * 0.5 Confidence label: medium. Primary evidence Whirlpool measurement source — 105533202.pdf + 105533202.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.625 + 2 * 0.5 = 36.625 in. Side evidence: Allow 1/2 in. space on each side. Open original source ↗ Why this value was used Minimum opening derived from exact product width plus explicit symmetric side spacing: 35.625 + 2 * 0.5 = 36.625 in. Side evidence: Allow 1/2 in. space on each side. Calculation or inference: 35.625 + 2 * 0.5. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.625 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 70.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in. Open original source ↗ Why this value was used Minimum opening height derived from highest stored appliance endpoint 70.125 in plus documented top clearance 0.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	25.25 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 25.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.25 in plus documented rear clearance 1.0 in. Open original source ↗ Why this value was used Minimum opening depth derived from case-only depth 24.25 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.5 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC2036R* Confidence label: high. Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 1/2" of space on each side Open original source ↗ Why this value was used 1/2" of space on each side Calculation or inference: documented DOE model pattern WRFC2036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.5 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC2036R* Confidence label: high. Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 1/2" of space on each side Open original source ↗ Why this value was used 1/2" of space on each side Calculation or inference: documented DOE model pattern WRFC2036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.5 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC2036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 1/2" of space on each side and at the top Open original source ↗ Why this value was used 1/2" of space on each side and at the top Calculation or inference: documented DOE model pattern WRFC2036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	1 in	✓ Verified — exact model · Calculated/inferred	Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool	Page 1
Value used by ExactFit 1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRFC2036R* Confidence label: medium. Primary evidence Whirlpool measurement source — dimension-guide-w11738607-reva.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-05 1" space behind Open original source ↗ Why this value was used 1" space behind Calculation or inference: documented DOE model pattern WRFC2036R*. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	3.75 in	✓ Verified — retained secondary source · Calculated/inferred	Whirlpool measurement source — 105160504.pdf assets.skulytics.io	Page 8
Value used by ExactFit 3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: cached document family mapping: generic_or_unscoped_shared_document Confidence label: medium. Primary evidence Whirlpool measurement source — 105160504.pdf assets.skulytics.io · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 8 Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33⁄4" (9.5 cm Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). next to a fixed wall, leave a 33⁄4" (9.5 cm Calculation or inference: cached document family mapping: generic_or_unscoped_shared_document. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.625 in	✓ Conflicting sources — resolved	Whirlpool installation document — 105533202.pdf assets.skulytics.io	Page 1
Value used by ExactFit 35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Whirlpool installation document — 105533202.pdf assets.skulytics.io · Installation manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-04 Width - Cabinet = 35-5/8 in. Open original source ↗ Why this value was used Width - Cabinet = 35-5/8 in. Other evidence found 45.3937 in — superseded The same document as the value used above; page 1. Model scope: not separately recorded. Raw value: Table Width Cabinet H: 45.3937". The final reviewed registry supersedes this earlier audit value. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Overall width

Selected: 35.625 in. Earlier retained values: 45.3937 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Width - Cabinet = 35-5/8 in.

View source scope, location, and impact on fit

Cabinet height

Selected: 68.875 in. Earlier retained values: 70.1181 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Height - Top of Cabinet = 68-7/8 in.

View source scope, location, and impact on fit

Height with hinge / controlling height

Selected: 70.125 in. Earlier retained values: 70.1181 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Height - Overall = 70-1/8 in.

View source scope, location, and impact on fit

Depth with door, without handles

Selected: 26.875 in. Earlier retained values: 42.9921 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth - Without Handles = 26-7/8 in.

View source scope, location, and impact on fit

Depth with handle

Selected: 30.5 in. Earlier retained values: 48.1102 in, 29.38 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Doors closed, handles included: 30 1/2 in; the sheet prints 26 7/8 in without handles and names WRFC2036R*.

View source scope, location, and impact on fit

Depth with doors open at 90°

Selected: 43 in. Earlier retained values: 68.8583 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Depth - Doors Open 90° = 43 in.

View source scope, location, and impact on fit

Cabinet case width

Selected: 35.625 in. Earlier retained values: 45.3937 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Width - Cabinet = 35-5/8 in.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Whirlpool installation document — 105533202.pdf

assets.skulytics.io · Installation manual · secondary model/source

Model numbers covered: WRFC2036RZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

7 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with doors open at 90°; Cabinet case width.