This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-09-05. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
Retained specification excerpt: Cabinet Width 24 in
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cabinet Width 24 in Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height To Top Of Cabinet 68.5 in
Value used by ExactFit
68.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Height To Top Of Cabinet 68.5 in Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Height To Top Of Door Hinge = 71.0 in | 62 cu. ft. Gross Weight 160.5 lbs Height 71 in Height To Top
Value used by ExactFit
71 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Height To Top Of Door Hinge = 71.0 in | 62 cu. ft. Gross Weight 160.5 lbs Height 71 in Height To Top Reviewed: 2026-09-04
Height To Top Of Door Hinge = 71.0 in | 62 cu. ft. Gross Weight 160.5 lbs Height 71 in Height To Top Of Cabinet 68.5 in Height To Top Of Door Hinge 71 in Net Weight 154.8 lbs Refrigerator Capacity Volume 9.36 Total Refrigerator Capac
Height To Top Of Door Hinge = 71.0 in | 62 cu. ft. Gross Weight 160.5 lbs Height 71 in Height To Top Of Cabinet 68.5 in Height To Top Of Door Hinge 71 in Net Weight 154.8 lbs Refrigerator Capacity Volume 9.36 Total Refrigerator Capac
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth Excluding Doors 24 in
Value used by ExactFit
24 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Excluding Doors 24 in Reviewed: 2026-09-04
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Depth Closed Excluding Handles 28.313 in
Value used by ExactFit
28.313 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Closed Excluding Handles 28.313 in Reviewed: 2026-09-04
Retained specification excerpt: Depth Closed Including Handles 28.375 in
Value used by ExactFit
28.375 in · Fit role: Traffic projection.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth Closed Including Handles 28.375 in Reviewed: 2026-09-04
Retained specification excerpt: Depth With Door Open 90 Degree 49 in
Value used by ExactFit
49 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth With Door Open 90 Degree 49 in Reviewed: 2026-09-04
25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 24.0 + 2 * 0.5
Confidence label: medium.
Primary evidence
Whirlpool WRB543CMJZ Owners Manual www.ajmadison.com · Owners Manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-04
Minimum opening derived from exact product width plus explicit symmetric side spacing: 24.0 + 2 * 0.5 = 25.0 in. Side evidence: To ensure proper ventilation for your refrigerator, it is | recommended to allow a 1/2" (1.25 cm) space on each side. | Allow 1 1/2" (3.81 cm) of space between overhead cabinets and | deterministic pattern: space_each_side
Minimum opening derived from exact product width plus explicit symmetric side spacing: 24.0 + 2 * 0.5 = 25.0 in. Side evidence: To ensure proper ventilation for your refrigerator, it is | recommended to allow a 1/2" (1.25 cm) space on each side. | Allow 1 1/2" (3.81 cm) of space between overhead cabinets and | deterministic pattern: space_each_side Calculation or inference: 24.0 + 2 * 0.5.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool opening envelope: max(68.5, 71.0) + 1.5 = 72.5 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202002/dimension-guide-w11440352.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 1.0 in.
Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 1.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRB543CMJ***
Confidence label: high.
Primary evidence
Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202002/dimension-guide-w11440352.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRB543CMJ***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
0.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRB543CMJ***
Confidence label: high.
Primary evidence
Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202002/dimension-guide-w11440352.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1/2" space on each side Calculation or inference: documented DOE model pattern WRB543CMJ***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool WRB543CMJZ Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, it is recommended to allow a 1/2" (1.27 cm) space on each side. Allow 1 1/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall (consider the condenser
Whirlpool installation manual explicit clearance: top_clearance_in=1.5 in. To ensure proper ventilation for your refrigerator, it is recommended to allow a 1/2" (1.27 cm) space on each side. Allow 1 1/2" (3.81 cm) of space between overhead cabinets and refrigerator top. Allow at least 1" (2.54 cm) between back of cabinet and the wall (consider the condenser
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: documented DOE model pattern WRB543CMJ***
Confidence label: medium.
Primary evidence
Whirlpool measurement source — https://www.whirlpool.com/content/dam/global/documents/202002/dimension-guide-w11440352.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
1" at the back Calculation or inference: documented DOE model pattern WRB543CMJ***.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Whirlpool WRB543CMJZ Dimension Guide assets.skulytics.io · Dimension Guide Model scope: Secondary source Publication/revision date: Not recorded Location: Page 2 Reviewed: 2026-09-05
space at the back for the water line connections. | If you are installing your refrigerator next to a fixed wall, leave 2 1/4 (5.7 cm) on the hinge side | to allow the door to swing open.
space at the back for the water line connections. | If you are installing your refrigerator next to a fixed wall, leave 2 1/4 (5.7 cm) on the hinge side | to allow the door to swing open.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Cabinet Width = 24.0 in | tion Configuration Refrigerator Refrigerator Type Bottom Freezer ### Dimen
Value used by ExactFit
24 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
24-inch Wide Garage-Ready Bottom-Freezer Refrigerator - 12.9 cu. ft. Fingerprint-Resistant Stainless Finish WRB543CMJZ | Whirlpool Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cabinet Width = 24.0 in | tion Configuration Refrigerator Refrigerator Type Bottom Freezer ### Dimen Reviewed: 2026-09-04
Cabinet Width = 24.0 in | tion Configuration Refrigerator Refrigerator Type Bottom Freezer ### Dimensions Cabinet Width 24 in Depth 28.375 in Depth Closed Excluding Handles 28.313 in Depth Closed Including
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: medium.
Primary evidence
Whirlpool WRB543CMJZ Owners Manual assets.skulytics.io · Owners Manual Model scope: Secondary source Publication/revision date: Not recorded Location: Page 5 Reviewed: 2026-09-04
To ensure proper ventilation for your refrigerator, it is | recommended to allow a 1/2" (1.25 cm) space on each side. | Allow 1 1/2" (3.81 cm) of space between overhead cabinets and | deterministic pattern: space_each_side
To ensure proper ventilation for your refrigerator, it is | recommended to allow a 1/2" (1.25 cm) space on each side. | Allow 1 1/2" (3.81 cm) of space between overhead cabinets and | deterministic pattern: space_each_side
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Model numbers covered: WRB543CMJZ. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
8 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.