This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Last reviewed: 2026-10-31. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
Retained specification excerpt: Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8"
Value used by ExactFit
32.625 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8" Reviewed: 2026-09-09
Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8"
Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8"
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105517247.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Popular-brand audit: exact endpoint for height_case_in is 68.5 in; replaces 70.0 in.
Popular-brand audit: exact endpoint for height_case_in is 68.5 in; replaces 70.0 in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105517247.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — wrb322dmb-dimension-guide-ajmadison-mirror.pdf assets.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
WRB322DMB table: Depth - Cabinet Only G -> 28 1/8 in
WRB322DMB table: Depth - Cabinet Only G -> 28 1/8 in
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105517247.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Popular-brand audit: exact endpoint for depth_less_handles_in is 30.875 in; replaces 33.375 in.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — 105517247.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-09
Retained specification excerpt: Depth with Door Open 90° 62"
Value used by ExactFit
62 in · Fit role: Operating clearance.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Depth with Door Open 90° 62" Reviewed: 2026-09-09
Retained specification excerpt: Whirlpool's installation documents for WRB322DMBM print no cutout width; they ask for 1/2 in of spac
Value used by ExactFit
33.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.
Original published value and unit: see retained transcription below. Normalization: 32.625 + 2 * 0.5 = 33.625
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf www.manualshelf.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Whirlpool's installation documents for WRB322DMBM print no cutout width; they ask for 1/2 in of spac Reviewed: 2026-10-31
Whirlpool's installation documents for WRB322DMBM print no cutout width; they ask for 1/2 in of space on each side: guide: 'Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear' Opening width = 32.625 + 1/2 + 1/2 = 33.625 in. The earlier 33.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all).
Whirlpool's installation documents for WRB322DMBM print no cutout width; they ask for 1/2 in of space on each side: guide: 'Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear' Opening width = 32.625 + 1/2 + 1/2 = 33.625 in. The earlier 33.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 32.625 + 2 * 0.5 = 33.625.
Other evidence found
33 in — superseded
Document 0c70048da07955b3eb97da78b532d8a3f5dfc7b4415166a34060898e8f477b95.html; page 1. Model scope: not separately recorded. Raw value: Cutout Width 33.0 in. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf www.manualshelf.com · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Calculated from the printed overall height 70 in plus Whirlpool's printed "allow 1/2" on top" = 70.5 Reviewed: 2026-09-18
Calculated from the printed overall height 70 in plus Whirlpool's printed "allow 1/2" on top" = 70.5 in. Replaces the whirlpool.com "Cutout Height" of 69 in, which was lower than the appliance itself. Owner decision 2026-09-18.
Calculated from the printed overall height 70 in plus Whirlpool's printed "allow 1/2" on top" = 70.5 in. Replaces the whirlpool.com "Cutout Height" of 69 in, which was lower than the appliance itself. Owner decision 2026-09-18. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Other evidence found
69 in — superseded
Document 0c70048da07955b3eb97da78b532d8a3f5dfc7b4415166a34060898e8f477b95.html; page 1. Model scope: not separately recorded. Raw value: Cutout Height 69.0 in. The final reviewed registry supersedes this earlier audit value.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
{"calculation": "depth_case_only_in + rear_clearance_in", "operands": {"depth_case_only_in": [{"cache_path": "data/sources/Whirlpool/WRB322DMBM/wrb322dmb-dimension-guide-ajmadison-mirror.pdf", "page": 1, "raw": "WRB322DMB table: Depth - Cabinet Only G -> 28 1/8 in", "source_url": "https://assets.ajmadison.com/ajmadison/itemdocs/wrb322dmb_specs_sheet.pdf", "value_in": 28.125}], "rear_clearance_in": [{"cache_path": "data/sources/Whirlpool/WRB322DMBM/specification-sheet-wrb322dmbspecsheetv01.pdf", "page": "PDF page 1, Cutout Dimensions row", "raw": "Cutout Dimensions Allow extra 1/2\" on sides and top Allow extra 1\" on rear", "source_url": "https://www.whirlpool.com/content/dam/global/documents/202001/specification-sheet-wrb322dmbspecsheetv01.pdf", "value_in": 1.0}]}, "result_in": 29.125} Calculation or inference: depth_case_only_in + rear_clearance_in.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear Reviewed: 2026-09-09
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear Reviewed: 2026-09-09
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Value used by ExactFit
0.5 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear Reviewed: 2026-09-09
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Value used by ExactFit
1 in · Fit role: Cavity fit.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf Whirlpool · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear Reviewed: 2026-09-09
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.
Original published value and unit: see retained transcription below. Normalization:
Confidence label: high.
Primary evidence
Whirlpool measurement source — wrb322dmb-dimension-guide-ajmadison-mirror.pdf assets.ajmadison.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 1 Reviewed: 2026-09-17
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). If installing next to a fixed wall, leave 2 1/2 in minimum on the hinge side to allow the door to swing open
Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). If installing next to a fixed wall, leave 2 1/2 in minimum on the hinge side to allow the door to swing open
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded
No retained excerpt is available.
The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.
Why this value was used
No evidence decision recorded.
Other evidence found
No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.
Effect on fit result
This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.
Retained specification excerpt: Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8"
Value used by ExactFit
32.625 in · Fit role: Informational only.
Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.
Confidence label: high.
Primary evidence
Whirlpool measurement source — specification-sheet-wrb322dmbspecsheetv01.pdf assets.skulytics.io · Web source Model scope: Not established Publication/revision date: Not recorded Location: Retained specification excerpt: Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8" Reviewed: 2026-09-09
Product Dimensions (H x W x D) 70" x 32-5/8" x 33-3/8"
Selected: 33.625 in. Earlier retained values: 33 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Whirlpool's installation documents for WRB322DMBM print no cutout width; they ask for 1/2 in of space on each side: guide: 'Cutout Dimensions Allow extra 1/2" on sides and top Allow extra 1" on rear' Opening width = 32.625 + 1/2 + 1/2 = 33.625 in. The earlier 33.0 in came from a product web page or store listing (Codex measurement review 2026-10-31, owner: check and fix all). Calculation or inference: 32.625 + 2 * 0.5 = 33.625.
Selected: 70.5 in. Earlier retained values: 69 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Calculated from the printed overall height 70 in plus Whirlpool's printed "allow 1/2" on top" = 70.5 in. Replaces the whirlpool.com "Cutout Height" of 69 in, which was lower than the appliance itself. Owner decision 2026-09-18. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.
Evidence reflects the sources reviewed on 2026-10-31. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.
