This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Bottom Freezer · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-14. 4 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 47.25 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit47.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5625 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5625 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 27 in | ✓ Conflicting sources — resolved | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit27 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 51 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit51 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 47.5 in | ✓ Conflicting sources — resolved | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit47.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Thermador measurement source — T48BT110NS-spec_sheet.pdf assets.ajmadison.com | Retained specification excerpt: Cutout Size (H x W x D) (in.) 84" | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T48BT110NS-spec_sheet.pdf Cutout Size (H x W x D) (in.) 84"Open original source ↗ Why this value was usedCutout Size (H x W x D) (in.) 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Verified — retained secondary source | Thermador measurement source — 101719810.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 101719810.pdf PLANNING NOTES | Width: The minimum required cutout width is 47 1/2" (1054 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install.Open original source ↗ Why this value was usedPLANNING NOTES | Width: The minimum required cutout width is 47 1/2" (1054 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — 101719810.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceThermador measurement source — 101719810.pdf Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedMinimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — 101719810.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Primary evidenceThermador measurement source — 101719810.pdf Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedMinimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.4375 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T48BT110NS-101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Minimum cutout height; Primary evidenceThermador measurement source — T48BT110NS-101719810.pdf Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch.Open original source ↗ Why this value was usedExact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_height_in - height_hinge_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0 in | ✓ Verified — retained secondary source | Thermador measurement source — 101719810.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Primary evidenceThermador measurement source — 101719810.pdf Manufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth.Open original source ↗ Why this value was usedManufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 0.875 in | ✓ Verified — retained secondary source | Thermador measurement source — 101719810.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceThermador measurement source — 101719810.pdf Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Flush-install top-view diagram labels 7/8 in at the 90-degree full-access door position.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Flush-install top-view diagram labels 7/8 in at the 90-degree full-access door position. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 11.5 in | ? Verified — finalized database measurement | Thermador measurement source — ff125ad02686187b72d1e9dfe2811d2928825ab5b9e873eaeee57b9578f47c34.pdf Publisher not recorded | Page 2 | |
Value used by ExactFit11.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — ff125ad02686187b72d1e9dfe2811d2928825ab5b9e873eaeee57b9578f47c34.pdf 11 1/2 in printed for flush installation. Read by the verification agent (run Dff125ad026) from a document naming the model. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used11 1/2 in printed for flush installation. Read by the verification agent (run Dff125ad026) from a document naming the model. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 47.25 in | ✓ Verified — retained secondary source | Thermador installation document — 101719810.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit47.25 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 101719810.pdf Thermador exact/chassis specification and flush-install top-view drawing.Open original source ↗ Why this value was usedThermador exact/chassis specification and flush-install top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 27 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador exact/chassis specification and flush-install top-view drawing.
View source scope, location, and impact on fitSelected: 47.5 in. Earlier retained values: 42 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador exact/chassis specification and flush-install top-view drawing.
View source scope, location, and impact on fitassets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: T48BT110NS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
14 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.ajmadison.com · Web source · secondary model/source
Model numbers covered: T48BT110NS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
1 displayed measurements supported: Minimum cutout height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: T48BT110NS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
1 displayed measurements supported: Top clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-14.
1 displayed measurements supported: Wall clearance for fully open door.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-14. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.