This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Unknown configuration · Unknown depth class
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-05. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 41.25 in | ✓ Secondary source only | [PDF] T42BT120NS s1.img-b.com | Page 2 | |
Value used by ExactFit41.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence[PDF] T42BT120NS Overall Width (Inches) = 41 1/4" | Overall Width (Inches) | 41 1/4" | Overall Height (Inches)Open original source ↗ Why this value was usedOverall Width (Inches) = 41 1/4" | Overall Width (Inches) | 41 1/4" | Overall Height (Inches) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 3 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Cabinet height. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.5625 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 3 | |
Value used by ExactFit83.5625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Height with hinge / controlling height. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Depth without door. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 2 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Depth with door, without handles. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 26.875 in | ✓ Conflicting sources — resolved · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 2 | |
Value used by ExactFit26.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Depth with handle. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 48 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 2 | |
Value used by ExactFit48 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Depth with doors open at 90°. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 41.5 in | ✓ Secondary source only | Thermador T42BT120NS Product Specification assets.skulytics.io | Page 4 | |
Value used by ExactFit41.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador T42BT120NS Product Specification PLANNING NOTES Width: The minimum required cutout width is 41 1/2" (1054 mm). Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install. Electrical Supply: The electrical supply outlet (A) is recommended to be located in an adjacent cabinet for safety and serviceability. If it is not possible due to the construction to connect the appliance to a power outlet next to it (A), connect the appliance to a power outlet behind the appliance (B). This alternative position of the power outlet is permissible only if you can switch off the outlet with a circuit breaker in the fuse box. Water Supply: A cold water supply is required for water dispenser and icemaker operation. Water pressure must be between 29 and 116 p.s.i. The water supply is recommended to be located in an adjacent cabinet or other area that can be accessed after the appliance is installed. Furniture Return: The pre-assembled metal frame hides unfinishedOpen original source ↗ Why this value was usedPLANNING NOTES Width: The minimum required cutout width is 41 1/2" (1054 mm). Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install. Electrical Supply: The electrical supply outlet (A) is recommended to be located in an adjacent cabinet for safety and serviceability. If it is not possible due to the construction to connect the appliance to a power outlet next to it (A), connect the appliance to a power outlet behind the appliance (B). This alternative position of the power outlet is permissible only if you can switch off the outlet with a circuit breaker in the fuse box. Water Supply: A cold water supply is required for water dispenser and icemaker operation. Water pressure must be between 29 and 116 p.s.i. The water supply is recommended to be located in an adjacent cabinet or other area that can be accessed after the appliance is installed. Furniture Return: The pre-assembled metal frame hides unfinished Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Secondary source only | [PDF] T42BT120NS s1.img-b.com | Retained specification excerpt: Cutout Size (HxWxD) (Inches) 84" | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence[PDF] T42BT120NS Cutout Size (HxWxD) (Inches) 84"Open original source ↗ Why this value was usedCutout Size (HxWxD) (Inches) 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ✓ Secondary source only | Thermador T42BT120NS Product Specification assets.skulytics.io | Page 4 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador T42BT120NS Product Specification PLANNING NOTES | Width: The minimum required cutout width is 41 1/2" (1054 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install.Open original source ↗ Why this value was usedPLANNING NOTES | Width: The minimum required cutout width is 41 1/2" (1054 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory-panel chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedMinimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width 110/120 factory-panel chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory-panel chassis. Measurement transferred: Left-side ventilation clearance. Relevant equivalence evidence: Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.. Known differences: not separately recorded. Review decision: documented chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory-panel chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.Open original source ↗ Why this value was usedMinimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side. Calculation or inference: same-width 110/120 factory-panel chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory-panel chassis. Measurement transferred: Right-side ventilation clearance. Relevant equivalence evidence: Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.. Known differences: not separately recorded. Review decision: documented chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.4375 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 2 | |
Value used by ExactFit0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in Confidence label: medium. Calculation inputs: Height with hinge / controlling height; Minimum cutout height; Primary evidenceThermador T42BT110NS Product Specification 84 in niche minus 83 9/16 in appliance height = 7/16 in.Open original source ↗ Why this value was used84 in niche minus 83 9/16 in appliance height = 7/16 in. Calculation or inference: min_cutout_height_in - height_hinge_in. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: min_cutout_height_in - height_hinge_in. Measurement transferred: Top clearance. Relevant equivalence evidence: 84 in niche minus 83 9/16 in appliance height = 7/16 in.. Known differences: not separately recorded. Review decision: documented cavity residual formula; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 4 | |
Value used by ExactFit0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory-panel chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Manufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth.Open original source ↗ Why this value was usedManufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth. Calculation or inference: same-width 110/120 factory-panel chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory-panel chassis. Measurement transferred: Rear clearance. Relevant equivalence evidence: Manufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth.. Known differences: not separately recorded. Review decision: documented chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Hinge-side wall clearance | 0.875 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 3 | |
Value used by ExactFit0.875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory-panel chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Flush-install top-view diagram labels 7/8 in at the 90-degree full-access door position.Open original source ↗ Why this value was usedFlush-install top-view diagram labels 7/8 in at the 90-degree full-access door position. Calculation or inference: same-width 110/120 factory-panel chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory-panel chassis. Measurement transferred: Hinge-side wall clearance. Relevant equivalence evidence: Flush-install top-view diagram labels 7/8 in at the 90-degree full-access door position.. Known differences: not separately recorded. Review decision: documented chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 41.25 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 3 | |
Value used by ExactFit41.25 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Cabinet case width. Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Adjoining-wall clearance (reviewed endpoint) | 0.375 in | ✓ Verified — equivalent model · Calculated/inferred | Thermador T42BT110NS Product Specification assets.skulytics.io | Page 3 | |
Value used by ExactFit0.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: same-width 110/120 factory chassis Confidence label: medium. Primary evidenceThermador T42BT110NS Product Specification Conflict-free left/right or handle-style sibling propagation.Open original source ↗ Why this value was usedConflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis. Why evidence from T42BT110NS appliesTarget model: T42BT120NS. Supporting model: T42BT110NS. Manufacturer: Thermador. Product family and measurement relationship: same-width 110/120 factory chassis. Measurement transferred: Adjoining-wall clearance (reviewed endpoint). Relevant equivalence evidence: Conflict-free left/right or handle-style sibling propagation.. Known differences: not separately recorded. Review decision: sibling chassis propagation; 2026-09-05. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 26.875 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Conflict-free left/right or handle-style sibling propagation. Calculation or inference: same-width 110/120 factory chassis.
View source scope, location, and impact on fits1.img-b.com · Web source · secondary model/source
Model numbers covered: T42BT120NS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Overall width; Minimum cutout height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product Specification · equivalent model/source
Model numbers covered: T42BT110NS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
13 displayed measurements supported: Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Hinge-side wall clearance; Cabinet case width; Adjoining-wall clearance (reviewed endpoint).
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Product Specification · secondary model/source
Model numbers covered: T42BT120NS. Publication/revision date: Not recorded. Reviewed: 2026-09-05.
2 displayed measurements supported: Minimum cutout width; Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-05. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.