This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Column Refrigerator · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-14. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.75 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 83.75 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 83.75 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 24.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Thermador measurement source — T36IR905SP-105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24-in appliance depth + standard 3/4-in furniture panel Confidence label: high. Primary evidenceThermador measurement source — T36IR905SP-105166495.pdf Exact-model Thermador pages visually verify a 24-in appliance body and the manufacturer planning branch based on a standard/typical 3/4-in furniture panel, yielding 24 3/4 in without a handle.Open original source ↗ Why this value was usedExact-model Thermador pages visually verify a 24-in appliance body and the manufacturer planning branch based on a standard/typical 3/4-in furniture panel, yielding 24 3/4 in without a handle. Calculation or inference: 24-in appliance depth + standard 3/4-in furniture panel. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 25.75 in | ✓ Conflicting sources — resolved · Calculated/inferred | Thermador measurement source — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24.75-in installed depth + standard 1-in handle Confidence label: medium. Primary evidenceThermador measurement source — 105166495.pdf Custom handle projection varies; standardized scenario.Open original source ↗ Why this value was usedCustom handle projection varies; standardized scenario. Calculation or inference: 24.75-in installed depth + standard 1-in handle. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 62.6875 in | ✓ Conflicting sources — resolved · Calculated/inferred | Thermador measurement source — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit62.6875 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 24 + 38 11/16 = 62 11/16 in Confidence label: high. Primary evidenceThermador measurement source — 105166495.pdf The drawing measures the door at 90° from the cabinet (or case) front: 38 11/16" ; top view: 24" (610 mm) from the back wall to the cabinet front. Stored from the back, like every other model: 24 + 38 11/16 = 62 11/16 in (owner decision 2026-10-14). The printed 38 11/16" is the front-of-cabinet figure.Open original source ↗ Why this value was usedThe drawing measures the door at 90° from the cabinet (or case) front: 38 11/16" ; top view: 24" (610 mm) from the back wall to the cabinet front. Stored from the back, like every other model: 24 + 38 11/16 = 62 11/16 in (owner decision 2026-10-14). The printed 38 11/16" is the front-of-cabinet figure. Calculation or inference: 24 + 38 11/16 = 62 11/16 in. Other evidence found
Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 84 in | ✓ Verified — retained secondary source | Thermador measurement source — 105166495.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 105166495.pdf Cutout Size (H x W x D) (in.) 84"Open original source ↗ Why this value was usedCutout Size (H x W x D) (in.) 84" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Thermador measurement source — 105166495.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 105166495.pdf Exact product sheet required cutout is 25 in deep; replaces the appliance-depth value 24 in.Open original source ↗ Why this value was usedExact product sheet required cutout is 25 in deep; replaces the appliance-depth value 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T36IR905SP-105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceThermador measurement source — T36IR905SP-105166495.pdf Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch.Open original source ↗ Why this value was usedExact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T36IR905SP-105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2 Confidence label: high. Calculation inputs: Minimum cutout width; Cabinet case width; Primary evidenceThermador measurement source — T36IR905SP-105166495.pdf Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch.Open original source ↗ Why this value was usedExact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch. Calculation or inference: (min_cutout_width_in - case_width_in) / 2. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.25 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T36IR905SP-105166495.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit0.25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Minimum cutout height; Primary evidenceThermador measurement source — T36IR905SP-105166495.pdf Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.25 in exactly for top_clearance_in while preserving the documented installation branch.Open original source ↗ Why this value was usedExact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.25 in exactly for top_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_height_in - height_hinge_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T36IR905SP-105166495.pdf assets.skulytics.io | Page 1 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceThermador measurement source — T36IR905SP-105166495.pdf Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 1 in exactly for rear_clearance_in while preserving the documented installation branch.Open original source ↗ Why this value was usedExact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 1 in exactly for rear_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.75 in | ✓ Verified — retained secondary source | Thermador installation document — 105166495.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.75 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 105166495.pdf Exact-model Thermador Freedom column sheet.Open original source ↗ Why this value was usedExact-model Thermador Freedom column sheet. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 24.75 in. Earlier retained values: 35.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model Thermador pages visually verify a 24-in appliance body and the manufacturer planning branch based on a standard/typical 3/4-in furniture panel, yielding 24 3/4 in without a handle. Calculation or inference: 24-in appliance depth + standard 3/4-in furniture panel.
View source scope, location, and impact on fitSelected: 25.75 in. Earlier retained values: 35.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Custom handle projection varies; standardized scenario. Calculation or inference: 24.75-in installed depth + standard 1-in handle.
View source scope, location, and impact on fitSelected: 62.6875 in. Earlier retained values: 38.6875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
The drawing measures the door at 90° from the cabinet (or case) front: 38 11/16" ; top view: 24" (610 mm) from the back wall to the cabinet front. Stored from the back, like every other model: 24 + 38 11/16 = 62 11/16 in (owner decision 2026-10-14). The printed 38 11/16" is the front-of-cabinet figure. Calculation or inference: 24 + 38 11/16 = 62 11/16 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: T36IR905SP. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
10 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: T36IR905SP. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
5 displayed measurements supported: Depth with door, without handles; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-10-14. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.