This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Verified — retained secondary source | Thermador installation document — 74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 74525224.pdf Overall Width (Inches) = 35 5/8" | Overall Width (Inches) | 35 5/8" | Overall Height (Inches)Open original source ↗ Why this value was usedOverall Width (Inches) = 35 5/8" | Overall Width (Inches) | 35 5/8" | Overall Height (Inches) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 71.5 in | ✓ Conflicting sources — resolved | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit71.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Product drawing labels cabinet height 71 1/2 in; 72 in includes the leveling-foot installation height.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Product drawing labels cabinet height 71 1/2 in; 72 in includes the leveling-foot installation height. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72 in | ✓ Verified — retained secondary source | Thermador installation document — 74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 74525224.pdf Overall Height (Inches) = 72" | Overall Height (Inches) | 72" | Overall Depth (Inches)Open original source ↗ Why this value was usedOverall Height (Inches) = 72" | Overall Height (Inches) | 72" | Overall Depth (Inches) Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 24 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Overall depth without hinges and doors 24 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Overall depth without hinges and doors 24 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.75 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Overall depth with hinges and doors, no handles, 28 3/4 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Overall depth with hinges and doors, no handles, 28 3/4 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 31.4375 in | ✓ Conflicting sources — resolved | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31.4375 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Overall depth 31 7/16 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Overall depth 31 7/16 in. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.375 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit43.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Top-view clearance drawing labels 43 3/8 in at 90 degrees.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Top-view clearance drawing labels 43 3/8 in at 90 degrees. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Thermador installation document — 74525224.pdf (p.4) assets.skulytics.io | Page 4 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 74525224.pdf (p.4) Required Cutout Size (HxWxD) (Inches) 72" x 36"x25"Open original source ↗ Why this value was usedRequired Cutout Size (HxWxD) (Inches) 72" x 36"x25" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit72.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Calculation inputs: Height with hinge / controlling height; Top clearance; Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: 72-in appliance plus the explicit 1/2-in top ventilation gap.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: 72-in appliance plus the explicit 1/2-in top ventilation gap. Calculation or inference: height_hinge_in + top_clearance_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Required cutout size is 72 x 36 x 25 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Required cutout size is 72 x 36 x 25 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Product installation drawing labels 1/8 in at both sides.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Product installation drawing labels 1/8 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Product installation drawing labels 1/8 in at both sides.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Product installation drawing labels 1/8 in at both sides. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Leave 1/2 in at the top for proper ventilation.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Leave 1/2 in at the top for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Leave 1 in behind for proper ventilation.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Leave 1 in behind for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.75 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit1.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model Thermador page visually verified: Top view labels 1 3/4 in on both hinge sides for 90-degree access.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Exact-model Thermador page visually verified: Top view labels 1 3/4 in on both hinge sides for 90-degree access. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FT820NS-74525224.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FT820NS-74525224.pdf Exact-model Thermador page visually verified: Overall width 35 5/8 in.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Overall width 35 5/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 71.5 in. Earlier retained values: 72 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model Thermador page visually verified: Product drawing labels cabinet height 71 1/2 in; 72 in includes the leveling-foot installation height.
View source scope, location, and impact on fitSelected: 31.4375 in. Earlier retained values: 31.125 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Exact-model Thermador page visually verified: Overall depth 31 7/16 in.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: T36FT820NS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
2 displayed measurements supported: Overall width; Height with hinge / controlling height.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: T36FT820NS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
13 displayed measurements supported: Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout height; Minimum cutout depth; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: T36FT820NS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Minimum cutout width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.