This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
French Door · Counter-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-24. 2 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 35.625 in | ✓ Conflicting sources — resolved | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.625 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence found
Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 72 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 72 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit72 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 25 in | ✓ Conflicting sources — resolved | Thermador measurement source — 91941274.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 91941274.pdf Cabinet depth 24 in excluding the 1 in fixed rear spacers; with the fixed spacers fitted the case-only depth is 25 in, which is also the required cutout depth. Rule B: case-only depth includes fixed rear spacers.Open original source ↗ Why this value was usedCabinet depth 24 in excluding the 1 in fixed rear spacers; with the fixed spacers fitted the case-only depth is 25 in, which is also the required cutout depth. Rule B: case-only depth includes fixed rear spacers. Other evidence found
Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 28.75 in | ✓ Conflicting sources — resolved | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.75 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 31.125 in | ✓ Conflicting sources — resolved | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31.125 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence found
Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 43.375 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit43.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 36 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit36 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 72.5 in | ✓ Verified — retained secondary source | Thermador measurement source — 91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit72.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: height_hinge_in + top_clearance_in Confidence label: high. Primary evidenceThermador measurement source — 91941274.pdf 72 in appliance height plus the explicit 1/2 in top ventilation gap = 72 1/2 in.Open original source ↗ Why this value was used72 in appliance height plus the explicit 1/2 in top ventilation gap = 72 1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 25 in | ✓ Verified — retained secondary source | Thermador measurement source — T36FL810NS-91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — T36FL810NS-91941274.pdf Exact-model Thermador page visually verified: Exact-model cutout drawing explicitly labels 25 in depth.Open original source ↗ All retained supporting links
Why this value was usedExact-model Thermador page visually verified: Exact-model cutout drawing explicitly labels 25 in depth. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — 91941274.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 91941274.pdf Exact product drawing labels 1/8 in side spacing.Open original source ↗ Why this value was usedExact product drawing labels 1/8 in side spacing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.125 in | ✓ Verified — retained secondary source | Thermador measurement source — 91941274.pdf assets.skulytics.io | Page 4 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador measurement source — 91941274.pdf Exact product drawing labels 1/8 in side spacing.Open original source ↗ Why this value was usedExact product drawing labels 1/8 in side spacing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.5 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit0.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Exact Thermador guide: leave 1/2 in gap at the top for proper ventilation.Open original source ↗ Why this value was usedExact Thermador guide: leave 1/2 in gap at the top for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Exact Thermador guide: leave 1 in behind for proper ventilation.Open original source ↗ Why this value was usedExact Thermador guide: leave 1 in behind for proper ventilation. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 1.75 in | ✓ Verified — retained secondary source | Thermador measurement source — 91941274.pdf assets.skulytics.io | Page 3 | |
Value used by ExactFit1.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidenceThermador measurement source — 91941274.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Legacy reviewed field migration; endpoint indicators=['90-degree']; Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (90 degrees). Legacy reviewed field migration; endpoint indicators=['90-degree']; Thermador freestanding specification and 90-degree top-view drawing. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 35.625 in | ✓ Conflicting sources — resolved | Thermador installation document — 91941274.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit35.625 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceThermador installation document — 91941274.pdf Thermador freestanding specification and 90-degree top-view drawing.Open original source ↗ Why this value was usedThermador freestanding specification and 90-degree top-view drawing. Other evidence found
Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 35.625 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador freestanding specification and 90-degree top-view drawing.
View source scope, location, and impact on fitSelected: 25 in. Earlier retained values: 24 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Cabinet depth 24 in excluding the 1 in fixed rear spacers; with the fixed spacers fitted the case-only depth is 25 in, which is also the required cutout depth. Rule B: case-only depth includes fixed rear spacers.
View source scope, location, and impact on fitSelected: 28.75 in. Earlier retained values: 25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador freestanding specification and 90-degree top-view drawing.
View source scope, location, and impact on fitSelected: 31.125 in. Earlier retained values: 25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador freestanding specification and 90-degree top-view drawing.
View source scope, location, and impact on fitSelected: 35.625 in. Earlier retained values: 36 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Thermador freestanding specification and 90-degree top-view drawing.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: T36FL810NS. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
15 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Minimum cutout width; Minimum cutout height; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Wall clearance for door open to 90°; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: T36FL810NS. Publication/revision date: Not recorded. Reviewed: 2026-09-11.
1 displayed measurements supported: Minimum cutout depth.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-24. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.