Measurement evidence for Thermador T36BT110NS

Value used by ExactFit

35.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

• 24 in — superseded

  static.pcrichard.com; location not retained. Model scope: not separately recorded. Raw value: l Height (Inches) 83 9/16 16" Min. - 85 1/2" Max. Overall Depth Without Panel or Handles (Inches) 24" Overall Depth With Panel (Inches) 24 3/4" Overall. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

45 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

• 1 in — superseded

  static.pcrichard.com; location not retained. Model scope: not separately recorded. Raw value: page 4 of 5 6 / 24 proud install top view clearance proud install cutout dimensions measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) ≥ 24 (≥ 610) 33/4 (95) 105/8 (270) 115° 115° 21 (533) 90° 90° (a) c 84 (2134) ≤ 71/4 (≤ 185) (b) ≥ 4 (≥ 100) (c) ≥ 4 (≥ 100) (c) c2 d ≥ 4 (≥ 100) (c) c1 ≥ 24 (≥ 610) 351/2-36 (900-914) c1: c2: d: c: b: a: furniture return frameless cabinet framed cabinet filler area for water and electric line routing socket measurements in inches (mm) t36bt110ns 36-inch built-in french door refrigerator, 2 drawer, pre-assembled freedom® collection, masterpiece® collection handles planning notes width: the minimum required cutout width is 35 1/2" (900 mm). depth: the minimum required cutout depth is 24" (610 mm). the refrigerator door panels will protrude [...] 1 800 735 4328 : 1 800 735 4328 . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 28773438_Thermador_Refrigeration_Planning_Installation_Guide.pdf
Thermador · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: cutout height of 84"
Reviewed: 2026-09-05

cutout height of 84"

Why this value was used

cutout height of 84"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BT110NS-101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Proud-install planning notes explicitly state a minimum required cutout depth of 24 in.

Why this value was used

Exact-model Thermador page visually verified: Proud-install planning notes explicitly state a minimum required cutout depth of 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Primary evidence

Thermador measurement source — 101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Primary evidence

Thermador measurement source — 101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Why this value was used

Minimum proud-install opening is 1/4 in wider than the appliance, giving 1/8 in per side.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Thermador measurement source — T36BT110NS-101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch.

Why this value was used

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_height_in - height_hinge_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Primary evidence

Thermador measurement source — 101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

Manufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth.

Why this value was used

Manufacturer proud-install plan permits a 24 in cavity equal to the 24 in appliance depth.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 101719930.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-14

Proud install top view: with the door at 90° it reaches 3 3/4" (95 mm) beyond the side of the appliance. The standard (proud) installation is stored (owner decision 2026-10-04 for built-ins).

Why this value was used

Proud install top view: with the door at 90° it reaches 3 3/4" (95 mm) beyond the side of the appliance. The standard (proud) installation is stored (owner decision 2026-10-04 for built-ins).

Other evidence found

• 0.875 in — superseded

  The same document as the value used above; page 3. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Flush-install top-view diagram labels 7/8 in at the 90-degree full-access door position.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

10.625 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 101719930.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-14

10 5/8 in printed for proud installation, factory stainless-steel panels and handles, door fully open t (larger of the printed per-door / standard-installation figures, owner rule). Read by the verification agent (run D4e8872d2b0) from a document naming the model.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

10 5/8 in printed for proud installation, factory stainless-steel panels and handles, door fully open t (larger of the printed per-door / standard-installation figures, owner rule). Read by the verification agent (run D4e8872d2b0) from a document naming the model.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.25 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 101719930.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.