Measurement evidence for Thermador T36BB120SS

Value used by ExactFit

35.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 22707422_T36BB120SS_36-IN_BUILT-IN_BOTTOM_FREEZER_REFRIGERATOR-2_DRAWER-PROFESSIONAL_SERIES_HANDLES-Specifications.pdf
askthermadorbestbuy.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Overall Width (Inches) = 35 1/4" | Overall Width (Inches) | 35 1/4" | Overall Height (Inches)

Why this value was used

Overall Width (Inches) = 35 1/4" | Overall Width (Inches) | 35 1/4" | Overall Height (Inches)

Other evidence found

• 1 in — superseded

  The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: page 4 of 5 5 / 24 proud install top view clearance proud install cutout dimensions measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) ≥ 24 (≥ 610) 33/4 (95) 181/4 (463) 115° 3815/16 (989) 90° (a) c 84 (2134) ≤ 71/4 (≤ 185) (b) ≥ 4 (≥ 100) (c) ≥ 4 (≥ 100) (c) c2 d ≥ 4 (≥ 100) (c) c1 ≥ 24 (≥ 610) 351/2-36 (900-914) c1: c2: d: c: b: a: furniture return frameless cabinet framed cabinet filler area for water and electric line routing socket measurements in inches (mm) t36bb120ss 36-inch built-in bottom freezer refrigerator, 2 drawer, pre-assembled freedom® collection, professional collection handles planning notes width: the minimum required cutout width is 35 1/2" (900 mm). depth: the minimum required cutout depth is 24" (610 mm). the refrigerator door panels will protrude [...] method to cabinetry 4 fixation brackets, fixed at 4 corners of appliance, no visible screws front serviceable yes anti-tip bracket included yes frame kit included yes technical specs required power supp. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall height minimum 83 9/16 in.

Why this value was used

Exact-model Thermador page visually verified: Overall height minimum 83 9/16 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall installed height minimum 83 9/16 in.

Why this value was used

Exact-model Thermador page visually verified: Overall installed height minimum 83 9/16 in.

Other evidence found

• 1 in — superseded

  askthermadorbestbuy.com; location not retained. Model scope: not separately recorded. Raw value: page 4 of 5 5 / 24 proud install top view clearance proud install cutout dimensions measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) ≥ 24 (≥ 610) 33/4 (95) 181/4 (463) 115° 3815/16 (989) 90° (a) c 84 (2134) ≤ 71/4 (≤ 185) (b) ≥ 4 (≥ 100) (c) ≥ 4 (≥ 100) (c) c2 d ≥ 4 (≥ 100) (c) c1 ≥ 24 (≥ 610) 351/2-36 (900-914) c1: c2: d: c: b: a: furniture return frameless cabinet framed cabinet filler area for water and electric line routing socket measurements in inches (mm) t36bb120ss 36-inch built-in bottom freezer refrigerator, 2 drawer, pre-assembled freedom® collection, professional collection handles planning notes width: the minimum required cutout width is 35 1/2" (900 mm). depth: the minimum required cutout depth is 24" (610 mm). the refrigerator door panels will protrude [...] method to cabinetry 4 fixation brackets, fixed at 4 corners of appliance, no visible screws front serviceable yes anti-tip bracket included yes frame kit included yes technical specs required power supp. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall depth without panel or handles 24 in.

Why this value was used

Exact-model Thermador page visually verified: Overall depth without panel or handles 24 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall depth with factory panel 24 3/4 in.

Why this value was used

Exact-model Thermador page visually verified: Overall depth with factory panel 24 3/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall depth with factory panel and handles 27.75 in.

Why this value was used

Exact-model Thermador page visually verified: Overall depth with factory panel and handles 27.75 in.

Other evidence found

• 1 in — superseded

  askthermadorbestbuy.com; location not retained. Model scope: not separately recorded. Raw value: page 4 of 5 5 / 24 proud install top view clearance proud install cutout dimensions measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) ≥ 24 (≥ 610) 33/4 (95) 181/4 (463) 115° 3815/16 (989) 90° (a) c 84 (2134) ≤ 71/4 (≤ 185) (b) ≥ 4 (≥ 100) (c) ≥ 4 (≥ 100) (c) c2 d ≥ 4 (≥ 100) (c) c1 ≥ 24 (≥ 610) 351/2-36 (900-914) c1: c2: d: c: b: a: furniture return frameless cabinet framed cabinet filler area for water and electric line routing socket measurements in inches (mm) t36bb120ss 36-inch built-in bottom freezer refrigerator, 2 drawer, pre-assembled freedom® collection, professional collection handles planning notes width: the minimum required cutout width is 35 1/2" (900 mm). depth: the minimum required cutout depth is 24" (610 mm). the refrigerator door panels will protrude [...] method to cabinetry 4 fixation brackets, fixed at 4 corners of appliance, no visible screws front serviceable yes anti-tip bracket included yes frame kit included yes technical specs required power supp. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 24 in — superseded

  askthermadorbestbuy.com; location not retained. Model scope: not separately recorded. Raw value: Height (Inches) 83 9/16 16" Min. - 85 1/2" Max." Overall Depth Without Panel or Handles (Inches) 24" Overall Depth With Panel (Inches) 24 3/4" Overall. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 26.875 in — superseded

  Document 101719915.pdf; page 2. Model scope: not separately recorded. Raw value: Conflict-free left/right or handle-style sibling propagation.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

62.9375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24 + 38 15/16 = 62 15/16 in

Confidence label: high.

Primary evidence

Thermador measurement source — 101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-14

The drawing measures the door at 90° from the cabinet (or case) front: 38 15/16" ; proud install: cabinet front at >= 24" (610 mm) from the back wall. Stored from the back, like every other model: 24 + 38 15/16 = 62 15/16 in (owner decision 2026-10-14). The printed 38 15/16" is the front-of-cabinet figure.

Why this value was used

The drawing measures the door at 90° from the cabinet (or case) front: 38 15/16" ; proud install: cabinet front at >= 24" (610 mm) from the back wall. Stored from the back, like every other model: 24 + 38 15/16 = 62 15/16 in (owner decision 2026-10-14). The printed 38 15/16" is the front-of-cabinet figure. Calculation or inference: 24 + 38 15/16 = 62 15/16 in.

Other evidence found

• 37.9375 in — superseded

  Document 101719915.pdf; page 2. Model scope: not separately recorded. Raw value: Conflict-free left/right or handle-style sibling propagation.. The final reviewed registry supersedes this earlier audit value.

• 38.9375 in — superseded

  assets.skulytics.io; page 4. Model scope: not separately recorded. Raw value: Exact-model Thermador page visually verified: Proud-install top view establishes 38.9375 in overall depth at 90 degrees.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Proud-install minimum cutout width 35.5 in.

Why this value was used

Exact-model Thermador page visually verified: Proud-install minimum cutout width 35.5 in.

Other evidence found

• 1 in — superseded

  askthermadorbestbuy.com; location not retained. Model scope: not separately recorded. Raw value: page 4 of 5 5 / 24 proud install top view clearance proud install cutout dimensions measurements in inches (mm) 351/2-36 (900-914) 1/8-3/8 (3-10) ≥ 24 (≥ 610) 33/4 (95) 181/4 (463) 115° 3815/16 (989) 90° (a) c 84 (2134) ≤ 71/4 (≤ 185) (b) ≥ 4 (≥ 100) (c) ≥ 4 (≥ 100) (c) c2 d ≥ 4 (≥ 100) (c) c1 ≥ 24 (≥ 610) 351/2-36 (900-914) c1: c2: d: c: b: a: furniture return frameless cabinet framed cabinet filler area for water and electric line routing socket measurements in inches (mm) t36bb120ss 36-inch built-in bottom freezer refrigerator, 2 drawer, pre-assembled freedom® collection, professional collection handles planning notes width: the minimum required cutout width is 35 1/2" (900 mm). depth: the minimum required cutout depth is 24" (610 mm). the refrigerator door panels will protrude [...] method to cabinetry 4 fixation brackets, fixed at 4 corners of appliance, no visible screws front serviceable yes anti-tip bracket included yes frame kit included yes technical specs required power supp. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 36 in — superseded

  www.ajmadison.com; location not retained. Model scope: not separately recorded. Raw value: 6 Inch. Depth: 24 3/4 Inch. Height: 83 9/16 Inch. Cutout Width: 36 Inch. Cutout Depth: 25 Inch. Cutout Height: 84 Inch.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Required cutout height 84 in.

Why this value was used

Exact-model Thermador page visually verified: Required cutout height 84 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-05

PLANNING NOTES | Width: The minimum required cutout width is 35 1/2" (900 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install.

Why this value was used

PLANNING NOTES | Width: The minimum required cutout width is 35 1/2" (900 mm). | Depth: The minimum required cutout depth is 24" (610 mm). The refrigerator door panels will protrude slightly for a proud install.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (minimum cutout width - appliance width) / 2

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Centered proud-install minimum opening leaves 1/8 in per side.

Why this value was used

Exact-model Thermador page visually verified: Centered proud-install minimum opening leaves 1/8 in per side. Calculation or inference: (minimum cutout width - appliance width) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (minimum cutout width - appliance width) / 2

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Centered proud-install minimum opening leaves 1/8 in per side.

Why this value was used

Exact-model Thermador page visually verified: Centered proud-install minimum opening leaves 1/8 in per side. Calculation or inference: (minimum cutout width - appliance width) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 84 - 83 9/16

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: 84-in niche minus 83 9/16-in minimum appliance height.

Why this value was used

Exact-model Thermador page visually verified: 84-in niche minus 83 9/16-in minimum appliance height. Calculation or inference: 84 - 83 9/16.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in proud cutout - 24-in appliance depth

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Proud-install cutout and appliance body are both 24 in deep.

Why this value was used

Exact-model Thermador page visually verified: Proud-install cutout and appliance body are both 24 in deep. Calculation or inference: 24-in proud cutout - 24-in appliance depth.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-14

Proud install top view: with the door at 90° it reaches 3 3/4" (95 mm) beyond the side of the appliance. The standard (proud) installation is stored (owner decision 2026-10-04 for built-ins).

Why this value was used

Proud install top view: with the door at 90° it reaches 3 3/4" (95 mm) beyond the side of the appliance. The standard (proud) installation is stored (owner decision 2026-10-04 for built-ins).

Other evidence found

• 0.875 in — superseded

  assets.skulytics.io; page 3. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Exact-model Thermador page visually verified: Flush-install detail B labels 7/8 in for 90-degree full access.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

18.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 101719896.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 4
Reviewed: 2026-10-14

18 1/4 in printed for proud installation. Read by the verification agent (run D008cc3d249) from a document naming the model.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

18 1/4 in printed for proud installation. Read by the verification agent (run D008cc3d249) from a document naming the model.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.25 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — T36BB120SS-101719896.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador page visually verified: Overall width 35.25 in.

Why this value was used

Exact-model Thermador page visually verified: Overall width 35.25 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.