Measurement evidence for Thermador T30IB100SP

Value used by ExactFit

29.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

83.5625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24-in appliance depth + standard 3/4-in furniture panel

Confidence label: high.

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador pages visually verify a 24-in appliance body and the manufacturer planning branch based on a standard/typical 3/4-in furniture panel, yielding 24 3/4 in without a handle.

Why this value was used

Exact-model Thermador pages visually verify a 24-in appliance body and the manufacturer planning branch based on a standard/typical 3/4-in furniture panel, yielding 24 3/4 in without a handle. Calculation or inference: 24-in appliance depth + standard 3/4-in furniture panel.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

26.875 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24.75-in panel depth + matching Thermador handle projection

Confidence label: medium.

Primary evidence

Thermador measurement source — 94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Handle projection transferred from the matching factory-handle chassis.

Why this value was used

Handle projection transferred from the matching factory-handle chassis. Calculation or inference: 24.75-in panel depth + matching Thermador handle projection.

Other evidence found

• 24 in — superseded

  www.ajmadison.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Depth = 24.0 in | Thermador T30IB100SP 30 Inch Panel Ready Built-In ... Quick Specs ; Width: 29 3/4 Inch ; Depth: 24 Inch ; Depth without Door and Handles: 24 Inch ; Height: 83 9/16 Inch ; Cutout Width: 30 Inch. . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

57 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 25 + 32 = 57 in

Confidence label: high.

Primary evidence

Thermador measurement source — 94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-14

The drawing measures the door at 90° from the cabinet (or case) front: 32" ; flush install: cabinet front at >= 25" (635 mm) from the back wall. Stored from the back, like every other model: 25 + 32 = 57 in (owner decision 2026-10-14). The printed 32" is the front-of-cabinet figure.

Why this value was used

The drawing measures the door at 90° from the cabinet (or case) front: 32" ; flush install: cabinet front at >= 25" (635 mm) from the back wall. Stored from the back, like every other model: 25 + 32 = 57 in (owner decision 2026-10-14). The printed 32" is the front-of-cabinet figure. Calculation or inference: 25 + 32 = 57 in.

Other evidence found

• 32 in — superseded

  The same document as the value used above; page 3. Model scope: not separately recorded. Raw value: Thermador exact/chassis specification and flush-install top-view drawing.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

30 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

84 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 28773438_Thermador_Refrigeration_Planning_Installation_Guide.pdf
Thermador · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: cutout height of 84"
Reviewed: 2026-09-05

cutout height of 84"

Why this value was used

cutout height of 84"

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Exact Thermador product sheet/flush-install plan requires a 25 in deep cavity.

Why this value was used

Exact Thermador product sheet/flush-install plan requires a 25 in deep cavity.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-11

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch.

Why this value was used

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: (min_cutout_width_in - case_width_in) / 2

Confidence label: high.

Calculation inputs: Minimum cutout width; Cabinet case width;

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-11

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch.

Why this value was used

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.125 in exactly for side_ventilation_clearance_in while preserving the documented installation branch. Calculation or inference: (min_cutout_width_in - case_width_in) / 2.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_height_in - height_hinge_in

Confidence label: high.

Calculation inputs: Height with hinge / controlling height; Minimum cutout height;

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch.

Why this value was used

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 0.4375 in exactly for top_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_height_in - height_hinge_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in

Confidence label: high.

Calculation inputs: Depth without door; Minimum cutout depth;

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-11

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 1 in exactly for rear_clearance_in while preserving the documented installation branch.

Why this value was used

Exact-model Thermador planning page visually verified. Printed installation and appliance operands reproduce 1 in exactly for rear_clearance_in while preserving the documented installation branch. Calculation or inference: min_cutout_depth_in - depth_case_only_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Thermador measurement source — T30IB100SP-94473656.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Exact-model Thermador page visually verified: Exact-model flush-install detail B labels 1 in at the 90-degree full-access hinge position; the former 7/8-in value belonged to wider chassis.

Why this value was used

Migrated from hinge_side_wall_clearance_in (90 degrees (text also gives a fully open figure)). Exact-model Thermador page visually verified: Exact-model flush-install detail B labels 1 in at the 90-degree full-access hinge position; the former 7/8-in value belonged to wider chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

13.1875 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador measurement source — 94473656.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-14

13 3/16 in printed for maximum door opening angle 115 degrees. Read by the verification agent (run D595ba1bd37) from a document naming the model.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

13 3/16 in printed for maximum door opening angle 115 degrees. Read by the verification agent (run D595ba1bd37) from a document naming the model.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Thermador installation document — 94473656.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Thermador exact/chassis specification and flush-install top-view drawing.

Why this value was used

Thermador exact/chassis specification and flush-install top-view drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.