This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Built-in French Door · Built-in
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-10-22. 1 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row identifies the model relationship and supporting evidence.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 48 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit48 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall width 48 in; the doors sit within it. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall width 48 in; the doors sit within it. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 84 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall height 84 in (2134 mm) including the top grille; height dimensions +/- 1/2 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall height 84 in (2134 mm) including the top grille; height dimensions +/- 1/2 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 84 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit84 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall height 84 in (2134 mm), height dimensions +/- 1/2 in (adjustable). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall height 84 in (2134 mm), height dimensions +/- 1/2 in (adjustable). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 23.875 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit23.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): 23 7/8 in (606 mm) from the rear of the unit to the front of the cabinet, excluding doors. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): 23 7/8 in (606 mm) from the rear of the unit to the front of the cabinet, excluding doors. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 26.1875 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit26.1875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall depth 26 3/16 in to the door face, excluding handles. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall depth 26 3/16 in to the door face, excluding handles. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Traffic projection. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 47.5 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit47.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening width 47 1/2 in for the 48 in model. 3 1/2 in finished returns required. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening width 47 1/2 in for the 48 in model. 3 1/2 in finished returns required. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 83.75 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit83.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening height 83 3/4 in (2127 mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening height 83 3/4 in (2127 mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 24 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening depth 24 in (610 mm). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.10: Opening Dimensions, standard installation: opening depth 24 in (610 mm). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Cavity fit. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 0.125 in | ? Verified — finalized database measurement · Calculated/inferred | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 10 | |
Value used by ExactFit0.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: min_cutout_depth_in - depth_case_only_in Confidence label: high. Calculation inputs: Depth without door; Minimum cutout depth; Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.10: Standard opening depth 24 in minus the 23 7/8 in case depth = 1/8 in behind the unit; no rear gap is printed separately. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.10: Standard opening depth 24 in minus the 23 7/8 in case depth = 1/8 in behind the unit; no rear gap is printed separately. Calculation or inference: min_cutout_depth_in - depth_case_only_in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.625 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit2.625 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8, Overall Dimensions top view: 2 5/8 in (67 mm) from the case side to the outer edge of the open door and handle, door at 90 degrees. Read the same way independently by the Hermes blind extraction (batch 23, door_projection_90_with_handle). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8, Overall Dimensions top view: 2 5/8 in (67 mm) from the case side to the outer edge of the open door and handle, door at 90 degrees. Read the same way independently by the Hermes blind extraction (batch 23, door_projection_90_with_handle). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | 10 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit10 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID), top view: door reach 10 in past each side with the doors open. For flush inset applications add 1/2 in to door clearance dimensions (p.6). The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID), top view: door reach 10 in past each side with the doors open. For flush inset applications add 1/2 in to door clearance dimensions (p.6). Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 48 in | ? Verified — finalized database measurement | Sub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Publisher not recorded | Page 8 | |
Value used by ExactFit48 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSub-Zero measurement source — ded1fa1543315ab0baa9fe7707f9cfcd8ba9ccca66cdf6555e9743697d04f5e8.pdf Sub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall width 48 in. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedSub-Zero Design Guide (revised 1/2025), p.8: Overall Dimensions, Model CL4850UFD(ID): overall width 48 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
An unknown required input can make the fit result Uncertain. Confirm the current exact-model installation document before purchase.
Publisher not recorded · Retained document · Scope not established
Model numbers covered: Not explicitly retained. Publication/revision date: Not recorded. Reviewed: 2026-10-22.
12 displayed measurements supported: Overall width; Cabinet height; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Rear clearance; Wall clearance for door open to 90°; Wall clearance for fully open door; Cabinet case width.
Availability: retained review record; original URL unavailable in the record.
Evidence reflects the sources reviewed on 2026-10-22. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.