This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.
Top Freezer · Standard-depth
Market status: Active (recorded 2026-08-17)
Last reviewed: 2026-09-17. 3 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.
Counts use distinct measurement records. Left and right ventilation share one per-side source record.
Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.
| Measurement | Value used | Evidence status | Primary source | Location | Details |
|---|---|---|---|---|---|
| Overall width | 32.875 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit32.875 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung installation document — 83051730.pdf Dimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8"Open original source ↗ Why this value was usedDimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Cabinet height | 66.75 in | ✓ Conflicting sources — resolved | Samsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit66.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf Product Dimensions height without hinges and door.Open original source ↗ All retained supporting links
Why this value was usedProduct Dimensions height without hinges and door. Other evidence found
Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Height with hinge / controlling height | 67.75 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit67.75 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung installation document — 83051730.pdf Dimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8"Open original source ↗ Why this value was usedDimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth without door | 28.5 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit28.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung installation document — 83051730.pdf Dimensions (WxHxD without hinges and door): 32 7/8" x 66 11/16" x 28 1/2"Open original source ↗ Why this value was usedDimensions (WxHxD without hinges and door): 32 7/8" x 66 11/16" x 28 1/2" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Depth with door, without handles | 31.875 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceSamsung installation document — 83051730.pdf WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8"Open original source ↗ Why this value was usedWxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with handle | 31.875 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit31.875 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung installation document — 83051730.pdf Dimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8"Open original source ↗ Why this value was usedDimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Depth with doors open at 90° | 64.75 in | ✓ Verified — retained secondary source | Samsung measurement source — 301367483 www.homedepot.com | Retained specification excerpt: Exact finish-model listing: Depth With Door Open 90 Degrees 64.75 in; rejected contradictory generat | |
Value used by ExactFit64.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidenceSamsung measurement source — 301367483 Exact finish-model listing: Depth With Door Open 90 Degrees 64.75 in; rejected contradictory generated summary value 59 7/8 in.Open original source ↗ Why this value was usedExact finish-model listing: Depth With Door Open 90 Degrees 64.75 in; rejected contradictory generated summary value 59 7/8 in. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Minimum cutout width | 33.625 in | ✓ Verified — retained secondary source · Calculated/inferred | Samsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit33.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 32.875 + 2 * 0.375 Confidence label: high. Primary evidenceSamsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf Closed product width plus the explicitly required clearance at each side.Open original source ↗ All retained supporting links
Why this value was usedClosed product width plus the explicitly required clearance at each side. Calculation or inference: 32.875 + 2 * 0.375. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout height | 68.125 in | ✓ Verified — retained secondary source · Calculated/inferred | Samsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit68.125 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 67.75 + 0.375 Confidence label: high. Primary evidenceSamsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf Height with hinges plus the explicitly required top clearance.Open original source ↗ All retained supporting links
Why this value was usedHeight with hinges plus the explicitly required top clearance. Calculation or inference: 67.75 + 0.375. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Minimum cutout depth | 29.5 in | ✓ Verified — retained secondary source · Calculated/inferred | Samsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit29.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: 28.5 + 1 Confidence label: high. Primary evidenceSamsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf Case depth without door plus the explicitly required rear clearance.Open original source ↗ All retained supporting links
Why this value was usedCase depth without door plus the explicitly required rear clearance. Calculation or inference: 28.5 + 1. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Left-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Samsung measurement source — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — 83051730.pdf Allow 3/8 in. minimum clearance at sides and top.Open original source ↗ Why this value was usedAllow 3/8 in. minimum clearance at sides and top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Right-side ventilation clearance | 0.375 in | ✓ Verified — retained secondary source | Samsung measurement source — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — 83051730.pdf Allow 3/8 in. minimum clearance at sides and top.Open original source ↗ Why this value was usedAllow 3/8 in. minimum clearance at sides and top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Top clearance | 0.375 in | ✓ Verified — retained secondary source | Samsung measurement source — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: top_clearance_in = reviewed side clearance because source explicitly states sides and top Confidence label: high. Primary evidenceSamsung measurement source — 83051730.pdf Stored reviewed evidence explicitly applies the same clearance to sides and top. Allow 3/8 in. minimum clearance at sides and top.Open original source ↗ Why this value was usedStored reviewed evidence explicitly applies the same clearance to sides and top. Allow 3/8 in. minimum clearance at sides and top. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Rear clearance | 1 in | ✓ Verified — retained secondary source | Samsung measurement source — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit1 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung measurement source — 83051730.pdf 1" minimum clearance at rearOpen original source ↗ Why this value was used1" minimum clearance at rear Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement | |||||
| Wall clearance for door open to 90° | 2.5 in | ✓ Verified — retained secondary source | Samsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit2.5 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidenceSamsung measurement source — RT21M6215_V5_SPEC_SHEET.pdf Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall.Open original source ↗ All retained supporting links
Why this value was usedMigrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Allow 2.5 in clearance on hinge side when installing next to a wall. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Wall clearance for fully open door | Unknown | ? Not found | Source not recorded Publisher not recorded | Exact location not retained | |
Value used by ExactFitUnknown · Fit role: Operating clearance. Primary evidenceSource not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was usedNo evidence decision recorded. Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
| Cabinet case width | 32.875 in | ✓ Verified — retained secondary source | Samsung installation document — 83051730.pdf assets.skulytics.io | Page 2 | |
Value used by ExactFit32.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidenceSamsung installation document — 83051730.pdf Dimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8"Open original source ↗ Why this value was usedDimensions (WxHxD with hinges, handles and doors): 32 7/8" x 67 3/4" x 31 7/8" Other evidence foundNo materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit resultThis is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement | |||||
Selected: 66.75 in. Earlier retained values: 66.6875 in. Endpoint definitions may differ; see the retained transcriptions and final review note.
Product Dimensions height without hinges and door.
View source scope, location, and impact on fitNot found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.
No evidence decision recorded.
Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.
assets.skulytics.io · Installation manual · secondary model/source
Model numbers covered: RT21M6215SRAA. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
10 displayed measurements supported: Overall width; Height with hinge / controlling height; Depth without door; Depth with door, without handles; Depth with handle; Left-side ventilation clearance; Right-side ventilation clearance; Top clearance; Rear clearance; Cabinet case width.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗assets.skulytics.io · Web source · secondary model/source
Model numbers covered: RT21M6215SRAA. Publication/revision date: Not recorded. Reviewed: 2026-09-17.
5 displayed measurements supported: Cabinet height; Minimum cutout width; Minimum cutout height; Minimum cutout depth; Wall clearance for door open to 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗www.homedepot.com · Web source · secondary model/source
Model numbers covered: RT21M6215SRAA. Publication/revision date: Not recorded. Reviewed: 2026-09-04.
1 displayed measurements supported: Depth with doors open at 90°.
Availability: retained review record; original URL retained (current availability not rechecked).
Open original source ↗Evidence reflects the sources reviewed on 2026-09-17. Manufacturer specifications can change. Confirm the current exact-model installation document and site-specific conditions before purchase or installation.