Measurement evidence for Samsung RT16A6195SRAA

Value used by ExactFit

27.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions width with hinges and doors.

Why this value was used

Product Dimensions width with hinges and doors.

Other evidence found

• 28.75 in — superseded

  www.abt.com; location not retained. Model scope: not separately recorded. Raw value: Exact-model table: Width 28.75 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

64.8 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 15-6-cu-ft-top-freezer-refrigerator-with-all-around-cooling-in-stainless-steel-sku-rt16a6195sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height without Hinge: 64.8 in | D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge
Reviewed: 2026-09-04

Height without Hinge: 64.8 in | D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge 66.875" Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Width 28.75" Depth without Door (in) 26" Heig

Why this value was used

Height without Hinge: 64.8 in | D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge 66.875" Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Width 28.75" Depth without Door (in) 26" Heig

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

66.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions height with hinges and doors.

Why this value was used

Product Dimensions height with hinges and doors.

Other evidence found

• 66.88 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Height with Hinge: 66.88 in | ensions W: 28 1/4" H: 70 1/4" D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge 66.875" Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Width 28.75" D. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 15-6-cu-ft-top-freezer-refrigerator-with-all-around-cooling-in-stainless-steel-sku-rt16a6195sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door: 26.0 in | " Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Wid
Reviewed: 2026-09-04

Depth without Door: 26.0 in | " Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Width 28.75" Depth without Door (in) 26" Height (decimal) 66.88 Width (decimal) 27.63 Depth (decimal) 29.25 Height (extr

Why this value was used

Depth without Door: 26.0 in | " Net Height without Hinge 64.8" Net Depth w/o Door Handle 66.875" Width 28.75" Depth without Door (in) 26" Height (decimal) 66.88 Width (decimal) 27.63 Depth (decimal) 29.25 Height (extr

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 2022-03-23-20-50-08.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model manufacturer product guide: Product Dimensions with Door without Handles 29 1/4 in.
Reviewed: 2026-09-04

Exact-model manufacturer product guide: Product Dimensions with Door without Handles 29 1/4 in.

Why this value was used

Exact-model manufacturer product guide: Product Dimensions with Door without Handles 29 1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

29.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 15-6-cu-ft-top-freezer-refrigerator-with-all-around-cooling-in-stainless-steel-sku-rt16a6195sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle: 29.25 in | 66 7/8" H x 26 1/4" D Shipping Dimensions W: 28 1/4" H: 70 1/4"
Reviewed: 2026-09-04

Depth with Door Handle: 29.25 in | 66 7/8" H x 26 1/4" D Shipping Dimensions W: 28 1/4" H: 70 1/4" D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge 66.875" Net Height without Hinge 64.8" Net Depth w/o Door

Why this value was used

Depth with Door Handle: 29.25 in | 66 7/8" H x 26 1/4" D Shipping Dimensions W: 28 1/4" H: 70 1/4" D: 30 1/8" Net Depth with Door Handle 29 1/4" Net Height with Hinge 66.875" Net Height without Hinge 64.8" Net Depth w/o Door

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

54.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 2022-03-23-20-50-08.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model manufacturer product guide: Product Dimensions with Doors Open 54 3/8 in.
Reviewed: 2026-09-04

Exact-model manufacturer product guide: Product Dimensions with Doors Open 54 3/8 in.

Why this value was used

Exact-model manufacturer product guide: Product Dimensions with Doors Open 54 3/8 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

31.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 27.875 + 2 * 2

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Closed product width plus the explicitly required clearance at each side.

Why this value was used

Closed product width plus the explicitly required clearance at each side. Calculation or inference: 27.875 + 2 * 2.

Other evidence found

• 29.5 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 29.5 in from product width 28.75 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 66.875 + 2

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Height with hinges plus the explicitly required top clearance.

Why this value was used

Height with hinges plus the explicitly required top clearance. Calculation or inference: 66.875 + 2.

Other evidence found

• 68.88 in — superseded

  dzrf1tezfwb3j.cloudfront.net; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 66.88 in appliance endpoint + 2 in clearance = 68.88 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 83051771.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Samsung installation envelope: 26 in appliance endpoint + 2 in clearance = 28 in.

Why this value was used

Samsung installation envelope: 26 in appliance endpoint + 2 in clearance = 28 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow 2 in minimum clearance at sides and top.

Why this value was used

Allow 2 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow 2 in minimum clearance at sides and top.

Why this value was used

Allow 2 in minimum clearance at sides and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 2022-03-23-20-50-08.pdf
dzrf1tezfwb3j.cloudfront.net · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 2" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 2" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 2" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Allow 2 in minimum clearance at rear.

Why this value was used

Allow 2 in minimum clearance at rear.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 5b9a9782056a785afc53fdcc83e822e55a185da45c7445a210e59f66624cff99.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 14
Reviewed: 2026-09-26

Minimum clearance along a wall to allow the door to open a full 90 degrees: 2 in.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Minimum clearance along a wall to allow the door to open a full 90 degrees: 2 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

27.625 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RT16A6195SR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Visually labeled cabinet/product width on the dimension drawing.

Why this value was used

Visually labeled cabinet/product width on the dimension drawing.

Other evidence found

• 28.75 in — superseded

  www.abt.com; location not retained. Model scope: not separately recorded. Raw value: Low-confidence same-appliance width mapping: case_width_in=28.75 in from width_doors_closed_in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 28.75 in — superseded

  www.abt.com; location not retained. Model scope: not separately recorded. Raw value: Same-appliance endpoint inference: case width equals exact stored closed width 28.75 in; manufacturer does not label a separate case-width endpoint.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.