Measurement evidence for Samsung RS22T5561SRAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions width with hinges and doors.

Why this value was used

Product Dimensions width with hinges and doors.

Other evidence found

• 35.88 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: Plain exact-model specification row: Width = 35.88 in | ng RS22T5561SRAA Side-by-Side Refrigerators | South Carolina | Appliance Home Store Inc | | | --- | | Width | 35.88 in. | | Height | 70.06 in. | | Length | Weight | 256 lbs. | | Shipping Weight | 265 lbs (Counter Depth) | | Shipping Weight. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions height without hinges and door.

Why this value was used

Product Dimensions height without hinges and door.

Other evidence found

• 68.62 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Height without Hinge: 68.62 in | inges or Handles 35 7/8" x 68 5/8" x 28 5/8" Net Height with Hinge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handle 28 5/8" Depth without Door (in) 24" (Counter Depth) H. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.0625 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions height with hinges and doors.

Why this value was used

Product Dimensions height with hinges and doors.

Other evidence found

• 70.06 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Height with Hinge: 70.06 in | 8" Product Dimensions without Hinges or Handles 35 7/8" x 68 5/8" x 28 5/8" Net Height with Hinge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handle 28 5/8" Depth withou. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 22-cu-ft-counter-depth-side-by-side-refrigerator-with-touch-screen-family-hub-in-stainless-steel-sku-rs22t5561sr-aa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door: 24.0 in | nge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handl
Reviewed: 2026-09-04

Depth without Door: 24.0 in | nge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handle 28 5/8" Depth without Door (in) 24" (Counter Depth) Height (decimal) 70.0625 Height (extra) \+ 2 inches for ventill

Why this value was used

Depth without Door: 24.0 in | nge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handle 28 5/8" Depth without Door (in) 24" (Counter Depth) Height (decimal) 70.0625 Height (extra) \+ 2 inches for ventill

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions closed depth without a projecting handle.

Why this value was used

Product Dimensions closed depth without a projecting handle.

Other evidence found

• 28.62 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Depth w/o Door Handle: 28.62 in | " x 28 5/8" Net Height with Hinge 70 1/16" Net Height without Hinge 68 5/8" Net Depth w/o Door Handle 28 5/8" Depth without Door (in) 24" (Counter Depth) Height (decimal) 70.0625 Height (ex. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.625 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Product Dimensions closed maximum depth including the shown handle configuration.

Why this value was used

Product Dimensions closed maximum depth including the shown handle configuration.

Other evidence found

• 28.62 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Depth with Door Handle: 28.62 in | 625 Product Dimensions without Door without Handles 35 7/8" x 68 5/8" x 24" Net Depth with Door Handle 28 5/8" (Counter Depth) Warranty 1 Year 1-Year Parts and Labor on Refrigerator 5 Years . The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

46.4375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
device.report · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Visually labeled 90-degree front-to-back envelope in the dimension drawing.

Why this value was used

Visually labeled 90-degree front-to-back envelope in the dimension drawing.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.875 + 2 * 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Closed product width plus the explicitly required clearance at each side.

Why this value was used

Closed product width plus the explicitly required clearance at each side. Calculation or inference: 35.875 + 2 * 0.375.

Other evidence found

• 36.63 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.63 in from product width 35.88 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.4375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 70.0625 + 0.375

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Height with hinges plus the explicitly required top clearance.

Why this value was used

Height with hinges plus the explicitly required top clearance. Calculation or inference: 70.0625 + 0.375.

Other evidence found

• 70.435 in — superseded

  s7d2.scene7.com; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 70.06 in appliance endpoint + 0.375 in clearance = 70.435 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

25 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 24 + 1

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Case depth without door plus the explicitly required rear clearance.

Why this value was used

Case depth without door plus the explicitly required rear clearance. Calculation or inference: 24 + 1.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — SamsungSpecs_980265120.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — SamsungSpecs_980265120.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — SamsungSpecs_980265120.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

1 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — SamsungSpecs_980265120.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow 1" minimum clearance at rear
Reviewed: 2026-09-05

Cached exact-model result: Allow 1" minimum clearance at rear

Why this value was used

Cached exact-model result: Allow 1" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Samsung measurement source — SamsungSpecs_980265120.pdf
s7d2.scene7.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or le
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 2.5" of clearance on hinge side

Why this value was used

Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 2.5" of clearance on hinge side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RS22T5561SR_V6.pdf
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-10

Visually labeled cabinet/product width on the dimension drawing.

Why this value was used

Visually labeled cabinet/product width on the dimension drawing.

Other evidence found

• 35.88 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: Low-confidence same-appliance width mapping: case_width_in=35.88 in from width_doors_closed_in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 35.88 in — superseded

  appliancehomestore.com; location not retained. Model scope: not separately recorded. Raw value: Same-appliance endpoint inference: case width equals exact stored closed width 35.88 in; manufacturer does not label a separate case-width endpoint.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.