Measurement evidence for Samsung RM80F23VMRAA

Value used by ExactFit

35.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RM80F23) from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 35.875 in from RM80F23VMR; at least three populated dimensions match a
Reviewed: 2026-09-04

Unanimous same-platform value 35.875 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Reviewed exact-model cached label: WIDTH = 35.875 in. Context: NOTE: Please allow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" WIDTH (FITS 36" OPENING) 35 7/ 8" DEPTH WITH D00R OPEN 43" [...] Please note: The above dimension and cutout information is for planning purpos

Why this value was used

Unanimous same-platform value 35.875 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Reviewed exact-model cached label: WIDTH = 35.875 in. Context: NOTE: Please allow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" WIDTH (FITS 36" OPENING) 35 7/ 8" DEPTH WITH D00R OPEN 43" [...] Please note: The above dimension and cutout information is for planning purpos Calculation or inference: Samsung platform-family propagation (RM80F23) from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied height_case_in=70.75 in from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rm80f23vmr
www.homery.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied height_case_in=70.75 in from RM80F23VMR
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied height_case_in=70.75 in from RM80F23VMR

Why this value was used

Same Samsung model with/without regional AA suffix; copied height_case_in=70.75 in from RM80F23VMR Calculation or inference: Same Samsung model with/without regional AA suffix; copied height_case_in=70.75 in from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied height_hinge_in=73.0 in from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied height_hinge_in=73.0 in from RM80F23VMR
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied height_hinge_in=73.0 in from RM80F23VMR

Why this value was used

Same Samsung model with/without regional AA suffix; copied height_hinge_in=73.0 in from RM80F23VMR Calculation or inference: Same Samsung model with/without regional AA suffix; copied height_hinge_in=73.0 in from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_case_only_in=24.0 in from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_case_only_in=24.0 in from RM80F23VM
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied depth_case_only_in=24.0 in from RM80F23VMR

Why this value was used

Same Samsung model with/without regional AA suffix; copied depth_case_only_in=24.0 in from RM80F23VMR Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_case_only_in=24.0 in from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 217362.html
www.abt.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model listing: Depth Without Handles 28.75 in.
Reviewed: 2026-09-04

Exact-model listing: Depth Without Handles 28.75 in.

Why this value was used

Exact-model listing: Depth Without Handles 28.75 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RM80F23) from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rm80f23vmr
www.homery.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 28.75 in from RM80F23VMR; at least three populated dimensions match an
Reviewed: 2026-09-04

Unanimous same-platform value 28.75 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Reviewed exact-model cached label: Depth = 28.75 in. Context: ainless Steel Back ### Dimensions Counter/Depth:Yes Exterior Width:36" Width:35 7/8" Depth:28 3/4" Height:72 1/2" Depth With Door Opened At 90 Degrees:43" Height Without Hinges:70 3/4" Depth Without Door:

Why this value was used

Unanimous same-platform value 28.75 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Reviewed exact-model cached label: Depth = 28.75 in. Context: ainless Steel Back ### Dimensions Counter/Depth:Yes Exterior Width:36" Width:35 7/8" Depth:28 3/4" Height:72 1/2" Depth With Door Opened At 90 Degrees:43" Height Without Hinges:70 3/4" Depth Without Door: Calculation or inference: Samsung platform-family propagation (RM80F23) from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rm80f23vmr
www.homery.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RM80F
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RM80F23VMR

Why this value was used

Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RM80F23VMR Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RM80F23) from RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf + WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 36.625 in from RM80F23VMR; at least three populated dimensions match a
Reviewed: 2026-09-04

Unanimous same-platform value 36.625 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Derived minimum opening width 36.625 in from product width 35.875 in and explicit 0.375 in clearance on each side.

Why this value was used

Unanimous same-platform value 36.625 in from RM80F23VMR; at least three populated dimensions match and none conflict. Donor evidence: Derived minimum opening width 36.625 in from product width 35.875 in and explicit 0.375 in clearance on each side. Calculation or inference: Samsung platform-family propagation (RM80F23) from RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

73.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 73.0 in plus propagated top clearance 0.375 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 73.0 in plus propagated top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-29

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-29

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RM80F23VMR

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RM80F23VMR.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RM80F23VMR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Exact-model Samsung fit guide: allow a 3/8" minimum clearance at sides and top.

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RM80F23VMR; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. Exact-model Samsung fit guide: allow a 3/8" minimum clearance at sides and top. Calculation or inference: exact 8-dimension chassis signature; source model Samsung RM80F23VMR.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF23DB9700QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF23DB9700QLAA_specification-sheet.pdf
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF23DB9700QLAA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF23DB9700QLAA; original evidence: 2” minimum clearance at rear

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF23DB9700QLAA; original evidence: 2” minimum clearance at rear Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF23DB9700QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — b1c0add1232cb80bdea6aa340fca87389c2e33619ba4b262827b2f69e101b84e.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-03

Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Allow 3 3/4 in of clearance when installing along a wall. This will allow for the door to open 90 degrees without the handle contacting the wall. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: matching exact regional-suffix chassis

Confidence label: medium.

Primary evidence

Samsung measurement source — Samsung RM80F23VMR matching chassis row
Samsung · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: RM80F23VMR case width is 35 7/8 in and every other structural dimension matches RM80F23VMRAA.
Reviewed: 2026-09-04

RM80F23VMR case width is 35 7/8 in and every other structural dimension matches RM80F23VMRAA.

Why this value was used

RM80F23VMR case width is 35 7/8 in and every other structural dimension matches RM80F23VMRAA. Calculation or inference: matching exact regional-suffix chassis.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.