Measurement evidence for Samsung RF90F29BECRAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

36" Bespoke AI 4-Door French Door Fridge | RF90F29BECRAA | Samsung Canada
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm
Reviewed: 2026-09-04

Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70.25 inch - Net Case Height without Hinge 68.87

Why this value was used

Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70.25 inch - Net Case Height without Hinge 68.87

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: RF90F29BECR dimensions without hinges and doors: height 68 7/8 in
Reviewed: 2026-09-04

RF90F29BECR dimensions without hinges and doors: height 68 7/8 in

Why this value was used

RF90F29BECR dimensions without hinges and doors: height 68 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: RF90F29BECR dimensions with hinges and doors: height 70 1/4 in
Reviewed: 2026-09-04

RF90F29BECR dimensions with hinges and doors: height 70 1/4 in

Why this value was used

RF90F29BECR dimensions with hinges and doors: height 70 1/4 in

Other evidence found

• 70 in — superseded

  https://images.thdstatic.com/catalog/pdfImages/26/26f0fe7f-dabe-4b52-9e31-576a1041188d.pdf; location not retained. Model scope: not separately recorded. Raw value: ch Door Refrigerator A B D DEPTH TO DOOR 341/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator Standard-depth refrig. The final reviewed registry supersedes this earlier audit value. RF90F29BECR dimensions with hinges and doors: height 70 1/4 in

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: RF90F29BECR dimensions without hinges and doors: depth 29 3/8 in
Reviewed: 2026-09-04

RF90F29BECR dimensions without hinges and doors: depth 29 3/8 in

Why this value was used

RF90F29BECR dimensions without hinges and doors: depth 29 3/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in = closed appliance depth because the documented design has no projecting exterior handle

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: No projecting exterior handle; depth less handles equals closed overall depth 34.25 in
Reviewed: 2026-09-04

No projecting exterior handle; depth less handles equals closed overall depth 34.25 in

Why this value was used

No projecting exterior handle; depth less handles equals closed overall depth 34.25 in Calculation or inference: depth_less_handles_in = closed appliance depth because the documented design has no projecting exterior handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

36" Bespoke AI 4-Door French Door Fridge | RF90F29BECRAA | Samsung Canada
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle: 34.25 in | Height with Hinge 70.25 inch - Net Case Height without Hinge 68.
Reviewed: 2026-09-04

Depth with Door Handle: 34.25 in | Height with Hinge 70.25 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 34.25 inch - Net Depth without Door Handle 34.25 inch - Net Depth without Door 29.375 in

Why this value was used

Depth with Door Handle: 34.25 in | Height with Hinge 70.25 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 34.25 inch - Net Depth without Door Handle 34.25 inch - Net Depth without Door 29.375 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

36" Bespoke AI 4-Door French Door Fridge | RF90F29BECRAA | Samsung Canada
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed cached exact-model manufacturer label: Depth with doors open at 90 = 43.0 in. Context: nche
Reviewed: 2026-09-04

Reviewed cached exact-model manufacturer label: Depth with doors open at 90 = 43.0 in. Context: nches. Detailed sizes for installation are explained in the following TOP view. Depth with doors open at 90º 43 inches, depth without doors 24 inches, install depth from the rear wall 26 inches, wid

Why this value was used

Reviewed cached exact-model manufacturer label: Depth with doors open at 90 = 43.0 in. Context: nches. Detailed sizes for installation are explained in the following TOP view. Depth with doors open at 90º 43 inches, depth without doors 24 inches, install depth from the rear wall 26 inches, wid

Other evidence found

• 48.5 in — superseded

  https://www.canadianappliance.ca/pdf/samsung/refrigerator/RF90F29BECRAA_sell-sheet.pdf; page 2. Model scope: not separately recorded. Raw value: RF90F29BECR 90-degree top-view product depth 48 1/2 in. The final reviewed registry supersedes this earlier audit value. Reviewed cached exact-model manufacturer label: Depth with doors open at 90 = 43.0 in. Context: nches. Detailed sizes for installation are explained in the following TOP view. Depth with doors open at 90º 43 inches, depth without doors 24 inches, install depth from the rear wall 26 inches, wid

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_clearance_wall_in = 36.5

Confidence label: high.

Calculation inputs: Overall width; Adjoining-wall clearance (reviewed endpoint);

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearan
Reviewed: 2026-09-04

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in

Why this value was used

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in Calculation or inference: width_doors_closed_in + 2 * side_clearance_wall_in = 36.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70.25 in appliance endpoint + 0.375 in clearance = 70.625 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70.25 in appliance endpoint + 0.375 in clearance = 70.625 in.

Why this value was used

Samsung installation envelope: 70.25 in appliance endpoint + 0.375 in clearance = 70.625 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.375 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: model-series prefix RF90F29; 3 direct seeds; unanimous value 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free 7-character model-series consensus (RF90F29) from 3 directly evidenced models; example
Reviewed: 2026-09-05

Conflict-free 7-character model-series consensus (RF90F29) from 3 directly evidenced models; example Samsung RF90F29AECEAA: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: model-series prefix RF90F29; 3 direct seeds; unanimous value 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free 7-character model-series consensus (RF90F29) from 3 directly evidenced models; example
Reviewed: 2026-09-05

Conflict-free 7-character model-series consensus (RF90F29) from 3 directly evidenced models; example Samsung RF90F29AECEAA: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 2 copy/copies, 1 domain(s
Reviewed: 2026-09-05

Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 2 copy/copies, 1 domain(s), official=False; no contrary parsed value.

Why this value was used

Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 2 copy/copies, 1 domain(s), official=False; no contrary parsed value.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 2" minimum clearance at rear
Reviewed: 2026-09-05

2" minimum clearance at rear

Why this value was used

2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

3. | Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Why this value was used

3. | Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: RF90F29BECR dimensions without hinges and doors: width 35 3/4 in
Reviewed: 2026-09-04

RF90F29BECR dimensions without hinges and doors: width 35 3/4 in

Why this value was used

RF90F29BECR dimensions without hinges and doors: width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Allow 3/8 in minimum clearance at sides
Reviewed: 2026-09-04

Allow 3/8 in minimum clearance at sides

Why this value was used

Allow 3/8 in minimum clearance at sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.