Measurement evidence for Samsung RF90F29AECRAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung AI Family Hub™ | AI Vision & Auto Open Door | 29 cu.ft.
basilappliance.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Plain exact-model specification row: Width = 35.75 in | Samsung AI Family Hub™ | AI Vision & Auto Op
Reviewed: 2026-09-04

Plain exact-model specification row: Width = 35.75 in | Samsung AI Family Hub™ | AI Vision & Auto Open Door | 29 cu.ft. Width, 35 3/4" ; Height (decimal), 70.25 ; Width (decimal), 35.75 ; Depth (decimal), 34.25 ; Height (extra), + 2 inches for ventillati

Why this value was used

Plain exact-model specification row: Width = 35.75 in | Samsung AI Family Hub™ | AI Vision & Auto Open Door | 29 cu.ft. Width, 35 3/4" ; Height (decimal), 70.25 ; Width (decimal), 35.75 ; Depth (decimal), 34.25 ; Height (extra), + 2 inches for ventillati

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RF90F29) from RF90F29BECR, RF90F29BECRAA

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 68.875 in from RF90F29BECR, RF90F29BECRAA; at least three populated di
Reviewed: 2026-09-04

Unanimous same-platform value 68.875 in from RF90F29BECR, RF90F29BECRAA; at least three populated dimensions match and none conflict. Donor evidence: Dimensions without hinges and doors: height 68 7/8 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 68.875 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

29 cu. ft. 4-Door French Door Refrigerator
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: ch Door Refrigerator A B D DEPTH TO DOOR 341/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator
Reviewed: 2026-09-04

ch Door Refrigerator A B D DEPTH TO DOOR 341/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator Standard-depth refrig

Why this value was used

ch Door Refrigerator A B D DEPTH TO DOOR 341/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator Standard-depth refrig

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RF90F29) from RF90F29BECR, RF90F29BECRAA

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 29.375 in from RF90F29BECR, RF90F29BECRAA; at least three populated di
Reviewed: 2026-09-04

Unanimous same-platform value 29.375 in from RF90F29BECR, RF90F29BECRAA; at least three populated dimensions match and none conflict. Donor evidence: Dimensions without hinges and doors: depth 29 3/8 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 29.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RF90F29) from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA

Confidence label: medium.

Primary evidence

Samsung Refrigerators RF90F29AECEAA (French 4-Door) ...
www.sangarfurniture.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 34.25 in from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA; at least thre
Reviewed: 2026-09-04

Unanimous same-platform value 34.25 in from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA; at least three populated dimensions match and none conflict. Donor evidence: Depth (Without Handles) = 34.25 in | , 35.75 inch(es) / 90.81 cm ; Height (With Hinge), 70.25 inch(es) / 178.44 cm ; Depth (Without Handles), 34.25 inch(es) /

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 34.25 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with AI Family Hub™+ & AI Vision Inside™ in Charcoal Glass and Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed exact-model cached label: Depth = 34.25 in. Context: or ventillation ![Depth](https://image
Reviewed: 2026-09-04

Reviewed exact-model cached label: Depth = 34.25 in. Context: or ventillation  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Why this value was used

Reviewed exact-model cached label: Depth = 34.25 in. Context: or ventillation  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung platform-family propagation (RF90F29) from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA

Confidence label: medium.

Primary evidence

Samsung 30.1 cu. ft. French Door Refrigerator RF30BB660012AA | Shop Appliances
www.shopappliances.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Unanimous same-platform value 48.5 in from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA; at least three
Reviewed: 2026-09-04

Unanimous same-platform value 48.5 in from RF90F29AECEAA, RF90F29BECR, RF90F29BECRAA; at least three populated dimensions match and none conflict. Donor evidence: Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_90_in=48.5 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_hinge_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Depth with Door Opened at 90 Degrees = 48.5 in | | 35 3/4" | | Depth | | Depth | 34 1/4" | | Depth without Handles | 34 1/4" | | Depth with Door Opened at 90 Degrees | 48 1/2" | | Counter-Depth | No | | Height | | Height | 70" | | Height without Hinges |

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 48.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — https://basilappliance.com/refrigeration/refrigerators/french-door-refrigerators/rf90f29aecraa + local-cache manufacturer-family consensus
basilappliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 36.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Bespoke 3-Door French Door Refrigerator (30 cu. ft.) with ...
www.nfm.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 70.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Bespoke French Door Fridge: RF30BB6200QLAA | Samsung Canada
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 29.375 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.375 in plus propagated rear clearance 2.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 31.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-05

Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

The retained record does not establish source scope or a resolvable supporting source.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-05

Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

The retained record does not establish source scope or a resolvable supporting source.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF30BB620012AA

Confidence label: medium.

Primary evidence

Bespoke 3-Door French Door Refrigerator (30 cu. ft.) with ...
www.nfm.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB620012AA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB620012AA; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 1 copy/copies, 1 domain(s), official=False; no contrary parsed value.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF30BB6200QLAA

Confidence label: medium.

Primary evidence

Bespoke French Door Fridge: RF30BB6200QLAA | Samsung Canada
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB6200QLAA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF30BB6200QLAA; original evidence: 2 inches of space in the back

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: model-series prefix RF90F29; 2 direct seeds; unanimous value 3.75

Confidence label: medium.

Primary evidence

RF90F29BECR
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free 7-character model-series consensus (RF90F29) from 2 directly evidenced models; example Samsung RF90F29BECR: 2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 3.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in mapped from populated width_doors_closed_in; doors do not materially change closed product width

Confidence label: low.

Primary evidence

Samsung AI Family Hub™ | AI Vision & Auto Open Door | 29 cu.ft.
basilappliance.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Low-confidence same-appliance width mapping: case_width_in=35.75 in from width_doors_closed_in.
Reviewed: 2026-09-04

Low-confidence same-appliance width mapping: case_width_in=35.75 in from width_doors_closed_in.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 35.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Popular-brand chassis/type consensus: Strong modal installation clearance for this manufacturer family

Confidence label: low.

Primary evidence

Samsung measurement source — local-cache manufacturer-family consensus
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pa
Reviewed: 2026-09-04

Inferred 0.375 in per-side installation clearance from dominant manufacturer-family specification pattern.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.