Measurement evidence for Samsung RF90F23EECRAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

RF90F23* page 19 width B: 35 6/8" (908 mm).

Why this value was used

RF90F23* page 19 width B: 35 6/8" (908 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

RF90F23* page 19 height C: 68 7/8" (1749 mm).

Why this value was used

RF90F23* page 19 height C: 68 7/8" (1749 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

RF90F23* page 19 overall height D: 70 1/4" (1785 mm).

Why this value was used

RF90F23* page 19 overall height D: 70 1/4" (1785 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

RF90F23* page 20 cabinet-body dimension 05: 24" (610 mm).

Why this value was used

RF90F23* page 20 cabinet-body dimension 05: 24" (610 mm).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-36-inch-23-cu-ft-counter-depth-french-4-door-refrigerator-with-ai-family-hub-rf90f23eecraa
www.merlinstv.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: More Width 35.75 inch(es) / 90.81 cm … 178.44 cm Depth (Without Handles) 28.75 inch(es)
Reviewed: 2026-09-04

More Width 35.75 inch(es) / 90.81 cm … 178.44 cm Depth (Without Handles) 28.75 inch(es)

Why this value was used

More Width 35.75 inch(es) / 90.81 cm … 178.44 cm Depth (Without Handles) 28.75 inch(es)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Recessed/handleless door design: overall closed depth equals depth with handles

Confidence label: medium.

Primary evidence

Samsung measurement source — 98469356.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

RF90F23* page 19 overall depth A: 28 6/8" (730 mm); no projecting handle.

Why this value was used

RF90F23* page 19 overall depth A: 28 6/8" (730 mm); no projecting handle. Calculation or inference: Recessed/handleless door design: overall closed depth equals depth with handles.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

RF70F23*/RF90F23* page 20 top-view dimension 07: 43" (1093 mm); dimension 08 is the farther drawer-open projection.

Why this value was used

RF70F23*/RF90F23* page 20 top-view dimension 07: 43" (1093 mm); dimension 08 is the farther drawer-open projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: 35.75 + 2 * 0.375 = 36.5 inches

Confidence label: medium.

Primary evidence

Samsung measurement source — 98469356.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

Exact width 35 3/4" plus the record's validated 3/8" installation clearance per side.

Why this value was used

Exact width 35 3/4" plus the record's validated 3/8" installation clearance per side. Calculation or inference: 35.75 + 2 * 0.375 = 36.5 inches.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.625 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.25 in plus propagated top clearanc
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.25 in plus propagated top clearance 0.375 in.

Why this value was used

Minimum opening height derived from highest appliance endpoint 70.25 in plus propagated top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.
Reviewed: 2026-10-29

Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.

Why this value was used

Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.
Reviewed: 2026-10-29

Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.

Why this value was used

Samsung RF90F23BECRAA sell sheet (same chassis): "Allow 3/8 in minimum clearance at sides" and top.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF90F23BECRAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original ev
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 1 copy/copies, 1 domain(s), official=False; no contrary parsed value.

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 1 copy/copies, 1 domain(s), official=False; no contrary parsed value. Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF90F23BECRAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF90F23BECRAA

Confidence label: medium.

Primary evidence

Samsung measurement source — RF90F23BECR_Specifications-Sheet_01.pdf
static.pcrichard.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original ev
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original evidence: 2" minimum clearance at rear

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF90F23BECRAA; original evidence: 2" minimum clearance at rear Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF90F23BECRAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — WillitFit_RF90F23BECR.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-25

Samsung Will-it-fit sheet for RF90F23BECR, the same RF90F23 cabinet (identical width, height and depth): "Allow 3 3/4" of clearance when installing along a wall" so the door opens 90 degrees without the handle contacting the wall. No separate sheet is published for this variant.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Samsung Will-it-fit sheet for RF90F23BECR, the same RF90F23 cabinet (identical width, height and depth): "Allow 3 3/4" of clearance when installing along a wall" so the door opens 90 degrees without the handle contacting the wall. No separate sheet is published for this variant. Calculation or inference: agent blind extraction visually confirmed.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Overall product width mapped to case width; closed doors do not change side-to-side width

Confidence label: medium.

Primary evidence

Samsung measurement source — 98469356.pdf
assets.skulytics.io · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-09-04

RF90F23* page 19 width B: 35 6/8" (908 mm).

Why this value was used

RF90F23* page 19 width B: 35 6/8" (908 mm). Calculation or inference: Overall product width mapped to case width; closed doors do not change side-to-side width.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.