Measurement evidence for Samsung RF90F23BECR

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

36" 23 Cu.Ft Bespoke AI French Door Fridge | RF90F23BECRAA | Samsung Canada
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. Net Width: 35.75 in | xHxD) 35.8 x 70.285 x 28.8 inches - Net Dimension (WxHxD) 908 x 1784 x 730 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70.25 inch - Net Case Height without Hinge 68.87

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 35.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

[PDF] RF90F23BECR - Canadian Appliance Source
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. RF90F23BECR dimensions without hinges and doors: height 68 7/8 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 68.875 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.28 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung Bespoke 36 in. 23 cu. ft. Counter Depth Stainless ...
www.homedepot.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height to Top of Door Hinge = 70.28 in | Samsung Bespoke 36 in. 23 cu. ft. Counter Depth Stainless .
Reviewed: 2026-09-04

Height to Top of Door Hinge = 70.28 in | Samsung Bespoke 36 in. 23 cu. ft. Counter Depth Stainless ... Height to Top of Door Hinge (in.) 70.28 in. Height to Top of Refrigerator Case (in.) 70.28 in. Height to Top of Refrigerato

Why this value was used

Height to Top of Door Hinge = 70.28 in | Samsung Bespoke 36 in. 23 cu. ft. Counter Depth Stainless ... Height to Top of Door Hinge (in.) 70.28 in. Height to Top of Refrigerator Case (in.) 70.28 in. Height to Top of Refrigerato

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

23 cu. ft. 4-Door French Door Refrigerator
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" [...] Be sure your new frid
Reviewed: 2026-09-04

ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" [...] Be sure your new fridge will fit Don't wait

Why this value was used

ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" [...] Be sure your new fridge will fit Don't wait

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Samsung RF90F23BECRAA cached regional-suffix chassis match

Confidence label: medium.

Primary evidence

Samsung 36 Inch 23 Cu.Ft. Bespoke AI Counter Depth 4-Door French Door
www.merlinstv.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung RF90F23BECRAA cached regional-suffix chassis match
Reviewed: 2026-09-04

Samsung RF90F23BECRAA cached regional-suffix chassis match

Why this value was used

Samsung RF90F23BECRAA cached regional-suffix chassis match Calculation or inference: Samsung RF90F23BECRAA cached regional-suffix chassis match.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

36" 23 Cu.Ft Bespoke AI French Door Fridge | RF90F23BECRAA | Samsung Canada
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. Depth with Door Handle: 28.75 in | Height with Hinge 70.25 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 28.75 inch - Net Depth without Door Handle 28.75 inch - Net Depth without Door 24 inch -

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 28.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

36" 23 Cu.Ft Bespoke AI French Door Fridge | RF90F23BECRAA | Samsung Canada
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. Depth with doors open at 90: 43.0 in | nches. Detailed sizes for installation are explained in the following TOP view. Depth with doors open at 90º 43 inches, depth without doors 24 inches, install depth from the rear wall 26 inches, wid

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 43 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

[PDF] RF90F23BECR - Canadian Appliance Source
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 36.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.28 in plus documented top clearance 0.375 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 70.655 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.0 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: top_clearance_in = reviewed side clearance because source explicitly states sides and top

Confidence label: high.

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Stored reviewed evidence explicitly applies the same clearance to sides and top. where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

Stored reviewed evidence explicitly applies the same clearance to sides and top. where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: 2" minimum clearance at rear
Reviewed: 2026-09-05

2" minimum clearance at rear

Why this value was used

2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

[PDF] RF90F23BECR - AJ Madison
assets.ajmadison.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Why this value was used

2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same Samsung model; AA regional suffix removed from RF90F23BECRAA

Confidence label: high.

Primary evidence

[PDF] RF90F23BECR - Canadian Appliance Source
www.canadianappliance.ca · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a
Reviewed: 2026-09-04

Regional-suffix sibling propagation from RF90F23BECRAA to RF90F23BECR; the base and AA model share a Samsung manual, their existing chassis dimensions agree, and no structural conflicts were found. RF90F23BECR dimensions without hinges and doors: width 35 3/4 in

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 35.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

RF90F23BECR
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.