Measurement evidence for Samsung RF70H30KEEAA

Value used by ExactFit

35.88 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Width (inch) 35.88 inch
Reviewed: 2026-09-04

Net Width (inch) 35.88 inch

Why this value was used

Net Width (inch) 35.88 inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.88 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-30-cuft-bespoke-ai-3-door-french-door-rf70h30keeaa
www.merlinstv.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Height without hinge = 68.88 in | es) 34 inch(es) / 86.36 cm Weight 282.19 lb(s) / 128 kg Additional
Reviewed: 2026-09-04

Height without hinge = 68.88 in | es) 34 inch(es) / 86.36 cm Weight 282.19 lb(s) / 128 kg Additional Dimensions • Height without hinge 68.88 in • Depth without door 29.44 in • +2 in ventilation clearance • +3 in door cleara

Why this value was used

Height without hinge = 68.88 in | es) 34 inch(es) / 86.36 cm Weight 282.19 lb(s) / 128 kg Additional Dimensions • Height without hinge 68.88 in • Depth without door 29.44 in • +2 in ventilation clearance • +3 in door cleara

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Case Height with Hinge 70.25 inch
Reviewed: 2026-09-04

Net Case Height with Hinge 70.25 inch

Why this value was used

Net Case Height with Hinge 70.25 inch

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.44 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth without Door = 29.44 in | Net Depth with Door Handle 34 inch Net Depth without Door Handle 31.
Reviewed: 2026-09-04

Depth without Door = 29.44 in | Net Depth with Door Handle 34 inch Net Depth without Door Handle 31.93 inch Net Depth without Door 29.44 inch Packing Dimension (WxHxD) 37 5/7 x 75 5/8 x 34 inch Net Weight 282.19 lb Pack

Why this value was used

Depth without Door = 29.44 in | Net Depth with Door Handle 34 inch Net Depth without Door Handle 31.93 inch Net Depth without Door 29.44 inch Packing Dimension (WxHxD) 37 5/7 x 75 5/8 x 34 inch Net Weight 282.19 lb Pack

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.93 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-30-cuft-bespoke-ai-3-door-french-door-rf70h30keeaa
www.merlinstv.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (Without Handles) = 31.93 in | ht (With Hinge) 70.25 inch(es) / 178.44 cm Overall Depth 34 inc
Reviewed: 2026-09-04

Depth (Without Handles) = 31.93 in | ht (With Hinge) 70.25 inch(es) / 178.44 cm Overall Depth 34 inch(es) / 86.36 cm Depth (Without Handles) 31.93 inch(es) / 81.1 cm Depth (With Handles) 34 inch(es) / 86.36 cm Weight 282.19 lb(s)

Why this value was used

Depth (Without Handles) = 31.93 in | ht (With Hinge) 70.25 inch(es) / 178.44 cm Overall Depth 34 inch(es) / 86.36 cm Depth (Without Handles) 31.93 inch(es) / 81.1 cm Depth (With Handles) 34 inch(es) / 86.36 cm Weight 282.19 lb(s)

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-30-cuft-bespoke-ai-3-door-french-door-rf70h30keeaa
www.merlinstv.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth (With Handles) = 34.0 in | l Depth 34 inch(es) / 86.36 cm Depth (Without Handles) 31.93 inch(e
Reviewed: 2026-09-04

Depth (With Handles) = 34.0 in | l Depth 34 inch(es) / 86.36 cm Depth (Without Handles) 31.93 inch(es) / 81.1 cm Depth (With Handles) 34 inch(es) / 86.36 cm Weight 282.19 lb(s) / 128 kg Additional Dimensions • Height wi

Why this value was used

Depth (With Handles) = 34.0 in | l Depth 34 inch(es) / 86.36 cm Depth (Without Handles) 31.93 inch(es) / 81.1 cm Depth (With Handles) 34 inch(es) / 86.36 cm Weight 282.19 lb(s) / 128 kg Additional Dimensions • Height wi

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model cached page: with both doors opened to 90 degrees, total depth is 48 1/4 in.
Reviewed: 2026-09-04

Official exact-model cached page: with both doors opened to 90 degrees, total depth is 48 1/4 in.

Why this value was used

Official exact-model cached page: with both doors opened to 90 degrees, total depth is 48 1/4 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30* and RF70H25*: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value.

Why this value was used

Recommended cabinet dimensions for RF70H30* and RF70H25*: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value.

Other evidence found

• 36.63 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.63 in from product width 35.88 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
www.merlinstv.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30*: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance.

Why this value was used

Recommended cabinet dimensions for RF70H30*: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance.

Other evidence found

• 72.25 in — superseded

  Document f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 70.25 in appliance endpoint + 2 in clearance = 72.25 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30*: depth D at least 33 7/8 in (860 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance.

Why this value was used

Recommended cabinet dimensions for RF70H30*: depth D at least 33 7/8 in (860 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance.

Other evidence found

• 31.44 in — superseded

  s1.img-b.com; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 29.44 in appliance endpoint + 2 in clearance = 31.44 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Samsung doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Samsung doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: RF70H25/RF70H30 shared installation platform

Confidence label: medium.

Primary evidence

Samsung measurement source — f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json
www.merlinstv.com · Web source
Model scope: Equivalent model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact RF70H product specification lists ventilation clearance +2 in height.
Reviewed: 2026-09-05

Exact RF70H product specification lists ventilation clearance +2 in height.

Why this value was used

Exact RF70H product specification lists ventilation clearance +2 in height. Calculation or inference: RF70H25/RF70H30 shared installation platform.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF70H30KERAA

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf70h30gee-specification-sheet.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF70H30KERAA: Cached exact-model result: Allow
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF70H30KERAA: Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Samsung documented sibling/platform propagation from RF70H30KERAA: Cached exact-model result: Allow 2" minimum clearance at rear Calculation or inference: shared Samsung model family; evidence donor RF70H30KERAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 7e2f09b2de300445439764f603aa64dc7f2da7bff48281fc1a2ff10f69e25fb0.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-25

Samsung RF70H30GE specification for the same RF70H30 cabinet (identical width, height and depth): "Please allow 3 3/4" of clearance when installing along a wall"; stored as for RF70H30GERAA.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Samsung RF70H30GE specification for the same RF70H30 cabinet (identical width, height and depth): "Please allow 3 3/4" of clearance when installing along a wall"; stored as for RF70H30GERAA. Calculation or inference: agent blind extraction visually confirmed.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.875 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 22
Reviewed: 2026-10-03

Clearance table for RF70H30* and RF70H25*: width B 35 7/8 in (912 mm). The stored 35 in was a retail net-width figure.

Why this value was used

Clearance table for RF70H30* and RF70H25*: width B 35 7/8 in (912 mm). The stored 35 in was a retail net-width figure.

Other evidence found

• 35 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 35.0 in; source_id=65987. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.