Measurement evidence for Samsung RF70H30GEEAA

Value used by ExactFit

35.88 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF70H30KEEAA, RF70H30KERAA

Confidence label: medium.

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Medium-confidence chassis inference from RF70H30KEEAA, RF70H30KERAA. Donors unanimously report width
Reviewed: 2026-09-04

Medium-confidence chassis inference from RF70H30KEEAA, RF70H30KERAA. Donors unanimously report width_doors_closed_in=35.88 in; at least four direct chassis dimensions match and none conflict. Matching fields: height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Net Width (inch) 35.88 inch

Why this value was used

Medium-confidence chassis inference from RF70H30KEEAA, RF70H30KERAA. Donors unanimously report width_doors_closed_in=35.88 in; at least four direct chassis dimensions match and none conflict. Matching fields: height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Net Width (inch) 35.88 inch Calculation or inference: same-brand product-class chassis propagation from RF70H30KEEAA, RF70H30KERAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.86 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf70h30geeaa
amdirectappliances.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: reviewed cached consensus: Height without Hinge = 68.86 in | es, Handles and Door","35.87 x 70.25 x
Reviewed: 2026-09-04

reviewed cached consensus: Height without Hinge = 68.86 in | es, Handles and Door","35.87 x 70.25 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product | supporting domains: amdirectappliances.com, appliancehomestore.com

Why this value was used

reviewed cached consensus: Height without Hinge = 68.86 in | es, Handles and Door","35.87 x 70.25 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product | supporting domains: amdirectappliances.com, appliancehomestore.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf70h30geeaa
amdirectappliances.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: reviewed cached consensus: Height with Hinge = 70.25 in | h","Product Dimensions with Hinges, Handle
Reviewed: 2026-09-04

reviewed cached consensus: Height with Hinge = 70.25 in | h","Product Dimensions with Hinges, Handles and Door","35.87 x 70.25 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth w | supporting domains: amdirectappliances.com, appliancehomestore.com

Why this value was used

reviewed cached consensus: Height with Hinge = 70.25 in | h","Product Dimensions with Hinges, Handles and Door","35.87 x 70.25 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth w | supporting domains: amdirectappliances.com, appliancehomestore.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.45 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf70h30geeaa
amdirectappliances.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: reviewed cached consensus: Depth without Door = 29.45 in | "70.25","Net Height without Hinge","68.86
Reviewed: 2026-09-04

reviewed cached consensus: Depth without Door = 29.45 in | "70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product Dimensions with hinge","Weight","Product Weight (lbs.)","306 lb","Ship | supporting domains: amdirectappliances.com, appliancehomestore.com

Why this value was used

reviewed cached consensus: Depth without Door = 29.45 in | "70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product Dimensions with hinge","Weight","Product Weight (lbs.)","306 lb","Ship | supporting domains: amdirectappliances.com, appliancehomestore.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.93 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf70h30geeaa
amdirectappliances.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: reviewed cached consensus: Depth w/o Door Handle = 31.93 in | 5 x 34","Net Height with Hinge","70.25
Reviewed: 2026-09-04

reviewed cached consensus: Depth w/o Door Handle = 31.93 in | 5 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product Dimensions with hinge","Weight","Pro | supporting domains: amdirectappliances.com, appliancehomestore.com

Why this value was used

reviewed cached consensus: Depth w/o Door Handle = 31.93 in | 5 x 34","Net Height with Hinge","70.25","Net Height without Hinge","68.86","Net Depth w/o Door Handle","31.93","Depth without Door (in)","29.45","Product Dimensions with hinge","Weight","Pro | supporting domains: amdirectappliances.com, appliancehomestore.com

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — rf70h30geeaa
appliancehomestore.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle = 34.0 in | ct Dimensions without Hinges and Door | 35.87 x 68.86 inch x 29.4
Reviewed: 2026-09-04

Depth with Door Handle = 34.0 in | ct Dimensions without Hinges and Door | 35.87 x 68.86 inch x 29.45 inch | | Net Depth with Door Handle | 34 inch | | Product Dimensions without Door without Handles | 35.87 x 70.25 x 29.45 i

Why this value was used

Depth with Door Handle = 34.0 in | ct Dimensions without Hinges and Door | 35.87 x 68.86 inch x 29.45 inch | | Net Depth with Door Handle | 34 inch | | Product Dimensions without Door without Handles | 35.87 x 70.25 x 29.45 i

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 236742.html
www.abt.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached specification: Depth With Door Open 90 Degrees 48.25 in.
Reviewed: 2026-09-04

Exact-model cached specification: Depth With Door Open 90 Degrees 48.25 in.

Why this value was used

Exact-model cached specification: Depth With Door Open 90 Degrees 48.25 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30* and RF70H25*: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value.

Why this value was used

Recommended cabinet dimensions for RF70H30* and RF70H25*: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value.

Other evidence found

• 36.63 in — superseded

  An earlier brand-wide assumption (no document for this model); location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.63 in from product width 35.88 in and explicit 0.375 in clearance on each side.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

71 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
amdirectappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30*: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance.

Why this value was used

Recommended cabinet dimensions for RF70H30*: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance.

Other evidence found

• 72.25 in — superseded

  Document f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 70.25 in appliance endpoint + 2 in clearance = 72.25 in.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 106221133.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 24
Reviewed: 2026-10-03

Recommended cabinet dimensions for RF70H30*: depth D at least 33 7/8 in (860 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance.

Why this value was used

Recommended cabinet dimensions for RF70H30*: depth D at least 33 7/8 in (860 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance.

Other evidence found

• 31.45 in — superseded

  s1.img-b.com; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 29.45 in appliance endpoint + 2 in clearance = 31.45 in.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Samsung doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model.

Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate)

Confidence label: low.

Primary evidence

ExactFit estimate (Samsung doesn't print this for the model)
ExactFit · Estimate
Model scope: Estimate from similar models
Publication/revision date: Not recorded
Location: Not printed for this model
Reviewed: 2026-10-29

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

No document we have for this model prints this value.

Why this value was used

Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 7e2f09b2de300445439764f603aa64dc7f2da7bff48281fc1a2ff10f69e25fb0.pdf
www.merlinstv.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-03

Installation Specifications: Allow a 3/8 in minimum clearance at top for ease of installation. The stored 2 in was carried over from a sibling platform.

Why this value was used

Installation Specifications: Allow a 3/8 in minimum clearance at top for ease of installation. The stored 2 in was carried over from a sibling platform.

Other evidence found

• 2 in — superseded

  Document f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json; location not retained. Model scope: not separately recorded. Raw value: Exact RF70H product specification lists ventilation clearance +2 in height.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF70H30GERAA

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf70h30gee-specification-sheet.pdf
s1.img-b.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF70H30GERAA: Cached exact-model result: Allow
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF70H30GERAA: Cached exact-model result: Allow 2" minimum clearance at rear

Why this value was used

Samsung documented sibling/platform propagation from RF70H30GERAA: Cached exact-model result: Allow 2" minimum clearance at rear Calculation or inference: shared Samsung model family; evidence donor RF70H30GERAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 7e2f09b2de300445439764f603aa64dc7f2da7bff48281fc1a2ff10f69e25fb0.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-14

Please allow 3 3/4" of clearance when installing along a wall; the starred 1 3/4" diagram figure is smaller. The largest door-swing clearance is stored (rule used since batch 13).

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Please allow 3 3/4" of clearance when installing along a wall; the starred 1 3/4" diagram figure is smaller. The largest door-swing clearance is stored (rule used since batch 13).

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.88 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

Samsung measurement source — rf80h-36-3dr-internal-dispenser-french-door-zero-clearance-fit-with-space-max-29-cu-ft-black-rf70h30keeaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same-appliance endpoint inference: case width equals exact stored closed width 35.88 in; manufacture
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.88 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.88 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.