Measurement evidence for Samsung RF70H25HERAA

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Samsung RF70H25HERAA fit check Check this model against your opening How ExactFit verifies measurements

Samsung RF70H25HERAA

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

9exact-model manufacturer values

1verified equivalent/same-chassis values

4secondary-source-only values

1estimated values (not printed for this model)

1values with unresolved source details

Last reviewed: 2026-10-29. 5 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from; estimated values are not printed for this model and come from similar models of the same brand.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.88 in	✓ Verified — exact model	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Net Width: 35.88 in \| (WxHxD) 35.9 x 70.25 x 29.5 inch - Net Dimension (WxHxD) 911 x 1784 x 749 mm
Value used by ExactFit 35.88 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Net Width: 35.88 in \| (WxHxD) 35.9 x 70.25 x 29.5 inch - Net Dimension (WxHxD) 911 x 1784 x 749 mm Reviewed: 2026-09-04 Net Width: 35.88 in \| (WxHxD) 35.9 x 70.25 x 29.5 inch - Net Dimension (WxHxD) 911 x 1784 x 749 mm - Net Width (inch) 35.88 inch - Net Height(inches) 70.25 inch - Net Case Height with Hinge 70.25 inch - Net Open original source ↗ Why this value was used Net Width: 35.88 in \| (WxHxD) 35.9 x 70.25 x 29.5 inch - Net Dimension (WxHxD) 911 x 1784 x 749 mm - Net Width (inch) 35.88 inch - Net Height(inches) 70.25 inch - Net Case Height with Hinge 70.25 inch - Net Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.88 in	✓ Conflicting sources — resolved	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Official exact-model page: Net Case Height without Hinge 68.88 in; 70.25 in is height with hinge.
Value used by ExactFit 68.88 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model page: Net Case Height without Hinge 68.88 in; 70.25 in is height with hinge. Reviewed: 2026-09-04 Official exact-model page: Net Case Height without Hinge 68.88 in; 70.25 in is height with hinge. Open original source ↗ Why this value was used Official exact-model page: Net Case Height without Hinge 68.88 in; 70.25 in is height with hinge. Other evidence found 70.25 in — superseded www.goemans.com; location not retained. Model scope: not separately recorded. Raw value: inch \| \| Net Height(inches) \| 70.25 inch \| \| Net Case Height with Hinge \| 70.25 inch \| \| Net Case Height without Hinge \| 68.88 inch . The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	70.25 in	✓ Verified — retained secondary source	Samsung measurement source — samsung-RF70H25HERAA www.goemans.com	Retained specification excerpt: \| \| Net Height(inches) \| 70.25 inch \| \| Net Case Height with Hinge \| 70.25 inch \| \| Net Case Height
Value used by ExactFit 70.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Samsung measurement source — samsung-RF70H25HERAA www.goemans.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: \| \| Net Height(inches) \| 70.25 inch \| \| Net Case Height with Hinge \| 70.25 inch \| \| Net Case Height Reviewed: 2026-09-04 \| \| Net Height(inches) \| 70.25 inch \| \| Net Case Height with Hinge \| 70.25 inch \| \| Net Case Height without Hinge \| 68.88 inch Open original source ↗ Why this value was used \| \| Net Height(inches) \| 70.25 inch \| \| Net Case Height with Hinge \| 70.25 inch \| \| Net Case Height without Hinge \| 68.88 inch Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	25 in	✓ Conflicting sources — resolved	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Official exact-model page: Net Depth without Door 25 in; 27.5 in is depth without handle.
Value used by ExactFit 25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model page: Net Depth without Door 25 in; 27.5 in is depth without handle. Reviewed: 2026-09-04 Official exact-model page: Net Depth without Door 25 in; 27.5 in is depth without handle. Open original source ↗ Why this value was used Official exact-model page: Net Depth without Door 25 in; 27.5 in is depth without handle. Other evidence found 27.5 in — superseded www.goemans.com; location not retained. Model scope: not separately recorded. Raw value: \| Net Depth with Door Handle \| 29.5 inch \| \| Net Depth without Door Handle \| 27.5 inch \| \| Net Depth without Door \| 25 inch \| \| Packin. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	27.5 in	✓ Conflicting sources — resolved	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Official exact-model page: Net Depth without Door Handle 27.5 in.
Value used by ExactFit 27.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model page: Net Depth without Door Handle 27.5 in. Reviewed: 2026-09-04 Official exact-model page: Net Depth without Door Handle 27.5 in. Open original source ↗ Why this value was used Official exact-model page: Net Depth without Door Handle 27.5 in. Other evidence found 27 in — superseded The same document as the value used above; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: depth_less_handles_in = 27.0 in; source_id=27261. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	29.5 in	✓ Verified — exact model	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Depth with Door Handle: 29.5 in \| e Height with Hinge 70.25 inch - Net Case Height without Hinge 68.
Value used by ExactFit 29.5 in · Fit role: Traffic projection. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Depth with Door Handle: 29.5 in \| e Height with Hinge 70.25 inch - Net Case Height without Hinge 68. Reviewed: 2026-09-04 Depth with Door Handle: 29.5 in \| e Height with Hinge 70.25 inch - Net Case Height without Hinge 68.88 inch - Net Depth with Door Handle 29.5 inch - Net Depth without Door Handle 27.5 inch - Net Depth without Door 25 inch - Open original source ↗ Why this value was used Depth with Door Handle: 29.5 in \| e Height with Hinge 70.25 inch - Net Case Height without Hinge 68.88 inch - Net Depth with Door Handle 29.5 inch - Net Depth without Door Handle 27.5 inch - Net Depth without Door 25 inch - Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	43.875 in	✓ Verified — exact model	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Official exact-model cached page: with both doors opened to 90 degrees, total depth is 43 7/8 in.
Value used by ExactFit 43.875 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Official exact-model cached page: with both doors opened to 90 degrees, total depth is 43 7/8 in. Reviewed: 2026-09-04 Official exact-model cached page: with both doors opened to 90 degrees, total depth is 43 7/8 in. Open original source ↗ Why this value was used Official exact-model cached page: with both doors opened to 90 degrees, total depth is 43 7/8 in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36.25 in	✓ Conflicting sources — resolved	Samsung measurement source — 106221133.pdf Samsung	Page 24
Value used by ExactFit 36.25 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — 106221133.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-10-03 Recommended cabinet dimensions for RF70H30* and RF70H25: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value. Open original source ↗ Why this value was used Recommended cabinet dimensions for RF70H30 and RF70H25: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value. Other evidence found 36.2 in — superseded* www.samsung.com + www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Derived minimum opening width 36.2 in from product width 35.88 in and explicit 0.16 in clearance on each side.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	71 in	✓ Conflicting sources — resolved	Samsung measurement source — 106221133.pdf www.goemans.com	Page 24
Value used by ExactFit 71 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — 106221133.pdf www.goemans.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-10-03 Recommended cabinet dimensions for RF70H25: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance. Open original source ↗ All retained supporting links www.goemans.com ↗ · Supporting model: RF70H25HERAA www.samsung.com ↗ · Supporting model: RF70H25HERAA Why this value was used Recommended cabinet dimensions for RF70H25: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance. Other evidence found 72.25 in — superseded Document f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 70.25 in appliance endpoint + 2 in clearance = 72.25 in.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	29.5 in	✓ Conflicting sources — resolved	Samsung measurement source — 106221133.pdf images.thdstatic.com	Page 24
Value used by ExactFit 29.5 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — 106221133.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Page 24 Reviewed: 2026-10-03 Recommended cabinet dimensions for RF70H25: depth D at least 29 1/2 in (748 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance. Open original source ↗ Why this value was used Recommended cabinet dimensions for RF70H25: depth D at least 29 1/2 in (748 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance. Other evidence found 27 in — superseded images.thdstatic.com; location not retained. Model scope: not separately recorded. Raw value: Samsung installation envelope: 25 in appliance endpoint + 2 in clearance = 27 in.. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.375 in	≈ Estimated — not printed for this model	ExactFit estimate (Samsung doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (Samsung doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.375 in	≈ Estimated — not printed for this model	ExactFit estimate (Samsung doesn't print this for the model) ExactFit	Not printed for this model
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Estimate — not printed in the documents for this model. Original published value and unit: see retained transcription below. Normalization: typical Samsung side gap (estimate) Confidence label: low. Primary evidence ExactFit estimate (Samsung doesn't print this for the model) ExactFit · Estimate Model scope: Estimate from similar models Publication/revision date: Not recorded Location: Not printed for this model Reviewed: 2026-10-29 Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer. No document we have for this model prints this value. Why this value was used Not printed in the Samsung documents we have for this model. 3/8 in is the side gap Samsung prints for similar models (RF27CG5400SRAA, RF32CG5100SRAA, RF70F29DERAA), so it is shown as an estimate. The fit check uses Samsung's cutout width for this model, so this estimate does not change the fit answer. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	2 in	✓ Verified — equivalent model · Calculated/inferred	Samsung measurement source — f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json www.merlinstv.com	Retained specification excerpt: Exact RF70H product specification lists ventilation clearance +2 in height.
Value used by ExactFit 2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: RF70H25/RF70H30 shared installation platform Confidence label: medium. Primary evidence Samsung measurement source — f4abeca549ddb9eefc5329f03d61378581ff75190618fc639736951cf8399f92.json www.merlinstv.com · Web source Model scope: Equivalent model Publication/revision date: Not recorded Location: Retained specification excerpt: Exact RF70H product specification lists ventilation clearance +2 in height. Reviewed: 2026-09-05 Exact RF70H product specification lists ventilation clearance +2 in height. Open original source ↗ Why this value was used Exact RF70H product specification lists ventilation clearance +2 in height. Calculation or inference: RF70H25/RF70H30 shared installation platform. Why evidence from RF70H30GERAA applies Target model: RF70H25HERAA. Supporting model: RF70H30GERAA. Manufacturer: Samsung. Product family and measurement relationship: RF70H25/RF70H30 shared installation platform. Measurement transferred: Top clearance. Relevant equivalence evidence: Exact RF70H product specification lists ventilation clearance +2 in height.. Known differences: not separately recorded. Reviewed 2026-10-29. This is not exact-model documentation. ExactFit applies it only to the measurement above because the retained evidence supports the stated equivalence. Supporting source ↗ Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	✓ Verified — retained secondary source	Samsung measurement source — 26f0fe7f-dabe-4b52-9e31-576a1041188d.pdf images.thdstatic.com	Retained specification excerpt: Cached exact-model result: Allow 2" minimum clearance at rear
Value used by ExactFit 2 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — 26f0fe7f-dabe-4b52-9e31-576a1041188d.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Cached exact-model result: Allow 2" minimum clearance at rear Reviewed: 2026-09-05 Cached exact-model result: Allow 2" minimum clearance at rear Open original source ↗ Why this value was used Cached exact-model result: Allow 2" minimum clearance at rear Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	0.16 in	✓ Verified — exact model	Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung	Retained specification excerpt: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or le
Value used by ExactFit 0.16 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Migrated from side_clearance_wall_in by documented endpoint semantics Confidence label: high. Primary evidence Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or le Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Legacy reviewed field migration; endpoint indicators=['side wall']; Exact-model Samsung page: maintains a 0.16-inch clearance from the side wall. Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in+side_clearance_wall_in (door angle not stated, 6 in or less). Legacy reviewed field migration; endpoint indicators=['side wall']; Exact-model Samsung page: maintains a 0.16-inch clearance from the side wall. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	Unknown	? Not found	Source not recorded Publisher not recorded	Exact location not retained
Value used by ExactFit Unknown · Fit role: Operating clearance. Primary evidence Source not recorded Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Exact location not retained Reviewed: Not recorded No retained excerpt is available. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used No evidence decision recorded. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.875 in	✓ Conflicting sources — resolved	Samsung measurement source — 106221133.pdf Samsung	Page 22
Value used by ExactFit 35.875 in · Fit role: Informational only. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — 106221133.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Page 22 Reviewed: 2026-10-03 Clearance table for RF70H30* and RF70H25: width B 35 7/8 in (912 mm). The stored 35 in was a retail net-width figure. Open original source ↗ Why this value was used Clearance table for RF70H30 and RF70H25: width B 35 7/8 in (912 mm). The stored 35 in was a retail net-width figure. Other evidence found 35 in — superseded* www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 35.0 in; source_id=27261. The final reviewed registry supersedes this earlier audit value. Open alternative source ↗ Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Cabinet height

Selected: 68.88 in. Earlier retained values: 70.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Official exact-model page: Net Case Height without Hinge 68.88 in; 70.25 in is height with hinge.

View source scope, location, and impact on fit

Depth without door

Selected: 25 in. Earlier retained values: 27.5 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Official exact-model page: Net Depth without Door 25 in; 27.5 in is depth without handle.

View source scope, location, and impact on fit

Depth with door, without handles

Selected: 27.5 in. Earlier retained values: 27 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Official exact-model page: Net Depth without Door Handle 27.5 in.

View source scope, location, and impact on fit

Minimum cutout width

Selected: 36.25 in. Earlier retained values: 36.2 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Recommended cabinet dimensions for RF70H30* and RF70H25*: width W at least 36 1/4 in (920 mm); the note says the cabinet must meet these minimum requirements. Replaces a calculated value.

View source scope, location, and impact on fit

Minimum cutout height

Selected: 71 in. Earlier retained values: 72.25 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Recommended cabinet dimensions for RF70H25*: height H at least 71 in (1803 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from height plus top clearance.

View source scope, location, and impact on fit

Minimum cutout depth

Selected: 29.5 in. Earlier retained values: 27 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Recommended cabinet dimensions for RF70H25*: depth D at least 29 1/2 in (748 mm); the note says the cabinet must meet these minimum requirements. Replaces a value calculated from case depth plus rear clearance.

View source scope, location, and impact on fit

Cabinet case width

Selected: 35.875 in. Earlier retained values: 35 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Clearance table for RF70H30* and RF70H25*: width B 35 7/8 in (912 mm). The stored 35 in was a retail net-width figure.

View source scope, location, and impact on fit

Measurements not established

Wall clearance for fully open door

Not found for safe fit use. Sources retained: None. No rejected related-model candidate is identified in the retained record.

No evidence decision recorded.

Verify this operating or informational measurement separately. Confirm the current exact-model installation document before purchase.

Source documents and pages

Samsung measurement source — rf80h-36-3dr-french-door-zero-clearance-fit-with-space-max-24-cu-ft-silver-rf70h25heraa

Samsung · Web source · exact model/source

Model numbers covered: RF70H25HERAA. Publication/revision date: Not recorded. Reviewed: 2026-09-17.

7 displayed measurements supported: Overall width; Cabinet height; Depth without door; Depth with door, without handles; Depth with handle; Depth with doors open at 90°; Wall clearance for door open to 90°.