Measurement evidence for Samsung RF70F29DERAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F29DER

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf70f29der.html
www.appliancepalace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F29DER

Why this value was used

Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F29DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F29DER.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105584242.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-10-03

Clearance table: RF70F29* C (height without hinge) 68 7/8 in (1749 mm), D (overall height) 70 in (1778 mm).

Why this value was used

Clearance table: RF70F29* C (height without hinge) 68 7/8 in (1749 mm), D (overall height) 70 in (1778 mm).

Other evidence found

• 68.75 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105584242.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-10-03

Clearance table: RF70F29* C (height without hinge) 68 7/8 in (1749 mm), D (overall height) 70 in (1778 mm). The model's own sheet prints 70 in too.

Why this value was used

Clearance table: RF70F29* C (height without hinge) 68 7/8 in (1749 mm), D (overall height) 70 in (1778 mm). The model's own sheet prints 70 in too.

Other evidence found

• 70.25 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Product Dimensions with Hinges, Handles and Door: 35 3/4 W x 70 1/4 H x 34 1/4 D.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105584242.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-10-03

Installation plan, callout 05 for RF70F29*: 29 3/8 in (748 mm); the model's own sheet prints 29 3/8 in without hinges and doors.

Why this value was used

Installation plan, callout 05 for RF70F29*: 29 3/8 in (748 mm); the model's own sheet prints 29 3/8 in without hinges and doors.

Other evidence found

• 29.5 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-29-cu-ft-4-door-french-door-refrigerator-with-inner-beverage-center-flexzone-drawer-in-stainless-steel-sku-rf70f29deraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.
Reviewed: 2026-09-04

Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Why this value was used

Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — bespoke-29-cu-ft-4-door-french-door-refrigerator-with-inner-beverage-center-flexzone-drawer-in-stainless-steel-sku-rf70f29deraa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches ![Depth](https://image-
Reviewed: 2026-09-04

Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Why this value was used

Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung installation document — 98469356.pdf
assets.skulytics.io · Installation manual
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

RF70F29*/RF90F29* page 20 top-view dimension 07: 48 2/4" (1231 mm); dimension 08 is the farther drawer-open projection.

Why this value was used

RF70F29*/RF90F29* page 20 top-view dimension 07: 48 2/4" (1231 mm); dimension 08 is the farther drawer-open projection.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf70f29der.html + RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: high.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-03

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 68.875, height_hinge_in = 70, top_clearance_in = 0.375 = 70.375 in (previously 70.625 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: max(height_case_in,height_hinge_in) + top_clearance_in with height_case_in = 68.875, height_hinge_in = 70, top_clearance_in = 0.375 = 70.375 in (previously 70.625 in). Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: high.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 89641a10a5b6d7f596d8763738d9926e35888a9c5b99b0a746cf53c6bfebf272.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-10-03

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 29.375, rear_clearance_in = 2 = 31.375 in (previously 31.5 in).

Why this value was used

Recalculated 2026-10-04 with the stored formula from current inputs: depth_case_only_in + rear_clearance_in with depth_case_only_in = 29.375, rear_clearance_in = 2 = 31.375 in (previously 31.5 in). Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: top_clearance_in = reviewed side clearance because source explicitly states sides and top

Confidence label: medium.

Primary evidence

Samsung measurement source — RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Stored reviewed evidence explicitly applies the same clearance to sides and top. where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

Stored reviewed evidence explicitly applies the same clearance to sides and top. where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 89641a10a5b6d7f596d8763738d9926e35888a9c5b99b0a746cf53c6bfebf272.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

2" minimum clearance at rear

Why this value was used

2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: medium.

Primary evidence

Samsung measurement source — RF70F29DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in = width_doors_closed_in

Confidence label: medium.

Calculation inputs: Overall width;

Primary evidence

Samsung measurement source — samsung-rf70f29der.html
www.appliancepalace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacture
Reviewed: 2026-09-09

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint.

Why this value was used

Same-appliance endpoint inference: case width equals exact stored closed width 35.75 in; manufacturer does not label a separate case-width endpoint. Calculation or inference: case_width_in = width_doors_closed_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.