Measurement evidence for Samsung RF70F29DER

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

SAMSUNG RF70F29DER
www.appliancepalace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Plain exact-model specification row: Width = 35.75 in | F29DER 36 Inch Freestanding French Door Smar
Reviewed: 2026-09-04

Plain exact-model specification row: Width = 35.75 in | F29DER 36 Inch Freestanding French Door Smart Refrigerator, 28.9 cu. ft. Capacity in Stainless Steel. Width: 35.75" Height: 70.00" Depth: 34.25" Energy Star Rated:

Why this value was used

Plain exact-model specification row: Width = 35.75 in | F29DER 36 Inch Freestanding French Door Smart Refrigerator, 28.9 cu. ft. Capacity in Stainless Steel. Width: 35.75" Height: 70.00" Depth: 34.25" Energy Star Rated:

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with Inner Beverage Center™ & FlexZone™ Drawer in Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.
Reviewed: 2026-09-04

Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.

Why this value was used

Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.25 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with Inner Beverage Center™ & FlexZone™ Drawer in Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product Dimensions with Hinges, Handles and Door: 35 3/4 W x 70 1/4 H x 34 1/4 D.
Reviewed: 2026-09-04

Product Dimensions with Hinges, Handles and Door: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Why this value was used

Product Dimensions with Hinges, Handles and Door: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Other evidence found

• 70 in — superseded

  https://www.nfm.com/on/demandware.static/-/Library-Sites-NFMSharedLibrary/default/dwe685d049/product-pdfs//062/05/62059894-assembly-instructions.pdf; location not retained. Model scope: not separately recorded. Raw value: DOOR 341/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will fit Don't wait until. The final reviewed registry supersedes this earlier audit value. Product Dimensions with Hinges, Handles and Door: 35 3/4 W x 70 1/4 H x 34 1/4 D.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with Inner Beverage Center™ & FlexZone™ Drawer in Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.
Reviewed: 2026-09-04

Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.

Why this value was used

Product Dimensions without Hinges and Door: 35 3/4 W x 68 3/4 H x 29 1/2 D.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with Inner Beverage Center™ & FlexZone™ Drawer in Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.
Reviewed: 2026-09-04

Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Why this value was used

Product Dimensions with Door without Handles: 35 3/4 W x 70 1/4 H x 34 1/4 D.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Bespoke 29 cu. ft. 4-Door French Door Refrigerator with Inner Beverage Center™ & FlexZone™ Drawer in Stainless Steel | Samsung US
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches ![Depth](https://image-
Reviewed: 2026-09-04

Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Why this value was used

Reviewed exact-model cached label: Depth = 34.25 in. Context: ight 70 Inches  Depth 34.25 Inches Make sure it fits Measure your space to assure it will fit upon delivery. and the pathway for a seamless de

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung RF90F23EECRAA User Manual
assets.skulytics.io · User Manual
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 20
Reviewed: 2026-09-04

RF70F29*/RF90F29* page 20 top-view dimension 07: 48 2/4" (1231 mm); dimension 08 is the farther drawer-open projection.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 48.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — https://www.appliancepalace.com/products/samsung-rf70f29der.html + https://image-us.samsung.com/SamsungUS/home/home-appliances/refrigerators/bespoke/03112025/rf70f29deraa/RF70F29DER_V8.pdf
www.appliancepalace.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening height derived from highest appliance endpoint 70.25 in plus propagated top clearance 0.375 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 70.625 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.5 in plus propagated rear clearance 2.0 in.

Why this value was used

A required calculation input lacks defensible evidence.

Retained research value: 31.5 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Samsung RF70F29DERAA: side_ventilation_clearance_in=0.375 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Samsung RF70F29DERAA: side_ventilation_clearance_in=0.375 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F29DERAA; original evidence: Stored reviewed evidence explicitly applies the same clearance to sides and top. where handle may make contact. | 4. Allow 2" minimum clearance at rear for proper air circulation and water/electrical | connections. Allow a 3/8" minimum clearance at sides and top for ease of installation. | deterministic pattern: minimum_sides

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 0.375 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F29DERAA; original evidence: 2" minimum clearance at rear

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 2 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

Unknown · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: identical 8-dimension chassis signature; propagated from RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-05

Conflict-free identical-chassis propagation from Samsung RF70F29DERAA: hinge_side_wall_clearance_in=3.75 in.

Why this value was used

The stored transfer does not identify both a supporting model and measurement-specific equivalence reasoning.

Retained research value: 3.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: case_width_in mapped from populated width_doors_closed_in; doors do not materially change closed product width

Confidence label: low.

Primary evidence

SAMSUNG RF70F29DER
www.appliancepalace.com · Web source
Model scope: Not established
Publication/revision date: Not recorded
Location: Retained specification excerpt: Low-confidence same-appliance width mapping: case_width_in=35.75 in from width_doors_closed_in.
Reviewed: 2026-09-04

Low-confidence same-appliance width mapping: case_width_in=35.75 in from width_doors_closed_in.

Why this value was used

A low-confidence, consensus, or unspecified-minimum assumption does not establish a safe fit requirement.

Retained research value: 35.75 in. It is preserved for audit but not accepted as a safe fit input.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

0.375 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied side_clearance_wall_in=0.375 in from RF70F29DERAA

Confidence label: medium.

Primary evidence

RF70F29DER 29 cu. ft. Bespoke 4-Door French Door Refrigerator
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-04

Same Samsung model with/without regional AA suffix; copied side_clearance_wall_in=0.375 in from RF70F29DERAA

Why this value was used

Same Samsung model with/without regional AA suffix; copied side_clearance_wall_in=0.375 in from RF70F29DERAA Calculation or inference: Same Samsung model with/without regional AA suffix; copied side_clearance_wall_in=0.375 in from RF70F29DERAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.