Measurement evidence for Samsung RF70F23DERAA

This page shows the sources and review decisions behind the measurements used by ExactFit. Evidence for the exact model is identified separately from verified equivalent-model or same-chassis evidence. Missing values remain Unknown.

Report a problem with this model Back to Samsung RF70F23DERAA fit check Check this model against your opening How ExactFit verifies measurements

Samsung RF70F23DERAA

French Door · Counter-depth
Market status: Active (recorded 2026-08-17)

View model fit check

Evidence summary

Complete mixed evidence

5exact-model manufacturer values

0verified equivalent/same-chassis values

10secondary-source-only values

1values with unresolved source details

Last reviewed: 2026-10-29. 7 retained source records. 0 unresolved conflicts. All inputs required by the cavity calculation are supported; an applicable cutout may replace additive requirements.

Counts use distinct measurement records. Left and right ventilation share one per-side source record.

Some measurements on this page are not supported by an exact-model document. Each affected row says where its value comes from.

Measurements and supporting evidence

Measurement	Value used	Evidence status	Primary source	Location
Overall width	35.75 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F
Value used by ExactFit 35.75 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied width_doors_closed_in=35.75 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Cabinet height	68.875 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER
Value used by ExactFit 68.875 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied height_case_in=68.875 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Height with hinge / controlling height	70 in	✓ Verified — retained secondary source	Samsung measurement source — 62059894-assembly-instructions.pdf www.nfm.com	Retained specification excerpt: DOOR 341/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will
Value used by ExactFit 70 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Samsung measurement source — 62059894-assembly-instructions.pdf www.nfm.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: DOOR 341/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will Reviewed: 2026-09-04 DOOR 341/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will fit Don't wait until Open original source ↗ Why this value was used DOOR 341/ 4 " WIDTH (FITS 36" OPENING) 35 3/ 4 " HEIGHT WITH HINGE 70" Be sure your new fridge will fit Don't wait until Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth without door	24 in	✓ Verified — exact model	Samsung measurement source — WillitFit_RF23BB8900_V2.pdf Samsung	Retained specification excerpt: 23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDT
Value used by ExactFit 24 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Samsung measurement source — WillitFit_RF23BB8900_V2.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: 23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDT Reviewed: 2026-09-04 23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDTH (FITS 36" OPENING) 3 Open original source ↗ Why this value was used 23 cu. ft. 4-Door French Door Refrigerator A B D DEPTH WITHOUT DOOR 24 " DEPTH TO DOOR 283/ 4 " WIDTH (FITS 36" OPENING) 3 Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Depth with door, without handles	28.75 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F
Value used by ExactFit 28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_less_handles_in=28.75 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with handle	28.75 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F
Value used by ExactFit 28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_with_handles_in=28.75 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Depth with doors open at 90°	43 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — RF70F23DER_V8_merged_specs.pdf www.theinsidersnet.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F
Value used by ExactFit 43 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — RF70F23DER_V8_merged_specs.pdf www.theinsidersnet.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied depth_doors_open_90_in=43.0 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Minimum cutout width	36.5 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23D
Value used by ExactFit 36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23D Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied min_cutout_width_in=36.5 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout height	70.375 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — RF70F23DER_V8.pdf Samsung	Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance
Value used by ExactFit 70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in Confidence label: medium. Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance; Primary evidence Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance Reviewed: 2026-09-05 Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in. Open original source ↗ Why this value was used Minimum opening height derived from highest appliance endpoint 70.0 in plus propagated top clearance 0.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Minimum cutout depth	26 in	✓ Verified — exact model · Calculated/inferred	Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung	Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.
Value used by ExactFit 26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in Confidence label: medium. Calculation inputs: Depth without door; Rear clearance; Primary evidence Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Reviewed: 2026-09-05 Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Open original source ↗ Why this value was used Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Left-side ventilation clearance	0.375 in	✓ Verified — exact model	Samsung measurement source — RF70F23DER_V8.pdf Samsung	Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an Reviewed: 2026-10-29 The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation." Open original source ↗ Why this value was used The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation." Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Right-side ventilation clearance	0.375 in	✓ Verified — exact model	Samsung measurement source — RF70F23DER_V8.pdf Samsung	Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: medium. Primary evidence Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an Reviewed: 2026-10-29 The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation." Open original source ↗ Why this value was used The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation." Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Top clearance	0.375 in	✓ Verified — exact model · Calculated/inferred	Samsung measurement source — RF70F23DER_V8.pdf Samsung	Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evide
Value used by ExactFit 0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — RF70F23DER_V8.pdf Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evide Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value. Open original source ↗ Why this value was used Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF70F23DER; original evidence: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value. Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Rear clearance	2 in	✓ Verified — exact model · Calculated/inferred	Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung	Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original e
Value used by ExactFit 2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA Confidence label: medium. Primary evidence Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa Samsung · Web source Model scope: Exact model Publication/revision date: Not recorded Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original e Reviewed: 2026-09-05 Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back Open original source ↗ Why this value was used Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit. Report this measurement
Wall clearance for door open to 90°	3.75 in	✓ Verified — retained secondary source	Samsung measurement source — RF70F23DER_V8_merged_specs.pdf www.theinsidersnet.com	Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model
Value used by ExactFit 3.75 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: Confidence label: high. Primary evidence Samsung measurement source — RF70F23DER_V8_merged_specs.pdf www.theinsidersnet.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model Reviewed: 2026-09-17 Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 3.75" of clearance on hinge side Open original source ↗ Why this value was used Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 3.75" of clearance on hinge side Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Wall clearance for fully open door	11.375 in	? Conflicting sources — resolved	Samsung measurement source — a4fd3effcdb1024963c267b690ea505f74f4f27db09b1ca8ebd3e591c095bf57.pdf Publisher not recorded	Page 3
Value used by ExactFit 11.375 in · Fit role: Operating clearance. Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding. Confidence label: high. Primary evidence Samsung measurement source — a4fd3effcdb1024963c267b690ea505f74f4f27db09b1ca8ebd3e591c095bf57.pdf Publisher not recorded · Retained document Model scope: Not established Publication/revision date: Not recorded Location: Page 3 Reviewed: 2026-10-15 Will-it-fit sheet "MODEL RF70F23DER DIMENSIONS", "TOP OF REFRIGERATOR WITH DOORS OPEN 125°": each door reaches 11 3/8 in past the cabinet side (58 1/2 in overall = 35 3/4 + 2 x 11 3/8). The sheet's 3 3/4 in note is the 90-degree handle clearance, stored as wall_clearance_door_90_in. The spec sheets (RF70F23DER_V8 and V10, p.2) and the user manual (p.20, RF70F23: 125°, 58 2/4 in, 11 3/8 in / 289 mm) print the same. The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above. Why this value was used Will-it-fit sheet "MODEL RF70F23DER DIMENSIONS", "TOP OF REFRIGERATOR WITH DOORS OPEN 125°": each door reaches 11 3/8 in past the cabinet side (58 1/2 in overall = 35 3/4 + 2 x 11 3/8). The sheet's 3 3/4 in note is the 90-degree handle clearance, stored as wall_clearance_door_90_in. The spec sheets (RF70F23DER_V8 and V10, p.2) and the user manual (p.20, RF70F23: 125°, 58 2/4 in, 11 3/8 in / 289 mm) print the same. Other evidence found 3.75 in — superseded Document 61dec54c62c2f9f4578f3152f25f116ebc0c8e46710417567d4fd39b547f87f0.pdf; page 2. Model scope: not separately recorded. Raw value: 3 3/4 in printed for installation along a wall. Read by the verification agent (run D61dec54c62) from a document naming the model.. The final reviewed registry supersedes this earlier audit value. Effect on fit result This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement
Cabinet case width	35.75 in	✓ Verified — retained secondary source · Calculated/inferred	Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com	Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER
Value used by ExactFit 35.75 in · Fit role: Informational only. Calculated or inferred value — not a directly printed measurement. Original published value and unit: see retained transcription below. Normalization: Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER Confidence label: medium. Primary evidence Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf images.thdstatic.com · Web source Model scope: Secondary source Publication/revision date: Not recorded Location: Retained specification excerpt: Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER Reviewed: 2026-09-04 Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER Open original source ↗ Why this value was used Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER Calculation or inference: Same Samsung model with/without regional AA suffix; copied case_width_in=35.75 in from RF70F23DER. Other evidence found No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched. Effect on fit result This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access. Report this measurement

Conflicting published measurements

Wall clearance for fully open door

Selected: 11.375 in. Earlier retained values: 3.75 in. Endpoint definitions may differ; see the retained transcriptions and final review note.

Will-it-fit sheet "MODEL RF70F23DER DIMENSIONS", "TOP OF REFRIGERATOR WITH DOORS OPEN 125°": each door reaches 11 3/8 in past the cabinet side (58 1/2 in overall = 35 3/4 + 2 x 11 3/8). The sheet's 3 3/4 in note is the 90-degree handle clearance, stored as wall_clearance_door_90_in. The spec sheets (RF70F23DER_V8 and V10, p.2) and the user manual (p.20, RF70F23*: 125°, 58 2/4 in, 11 3/8 in / 289 mm) print the same.

View source scope, location, and impact on fit

Source documents and pages

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf

images.thdstatic.com · Web source · secondary model/source

Model numbers covered: RF70F23DERAA. Publication/revision date: Not recorded. Reviewed: 2026-09-04.

6 displayed measurements supported: Overall width; Cabinet height; Depth with door, without handles; Depth with handle; Minimum cutout width; Cabinet case width.