Measurement evidence for Samsung RF70F23DER

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product width 35 3/4 in
Reviewed: 2026-09-04

Product width 35 3/4 in

Why this value was used

Product width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and doors: height 68 7/8 in
Reviewed: 2026-09-04

Dimensions without hinges and doors: height 68 7/8 in

Why this value was used

Dimensions without hinges and doors: height 68 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF70F23DER_V8_merged_specs.pdf
www.theinsidersnet.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: e narrowest opening. A B D DEPTH TO DOOR 283/ 4 " HEIGHT WITH HINGE 70" Counter-Depth Refrigerator C
Reviewed: 2026-09-04

e narrowest opening. A B D DEPTH TO DOOR 283/ 4 " HEIGHT WITH HINGE 70" Counter-Depth Refrigerator Counter-depth models s

Why this value was used

e narrowest opening. A B D DEPTH TO DOOR 283/ 4 " HEIGHT WITH HINGE 70" Counter-Depth Refrigerator Counter-depth models s

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

24 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF70F23DER_V8_merged_specs.pdf
www.theinsidersnet.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" RF70F23DER 23 cu. ft. Bespo
Reviewed: 2026-09-04

ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" RF70F23DER 23 cu. ft. Bespoke Counter Depth 4-Doo

Why this value was used

ow 3¾" of clearance when installing along a wall. DEPTH WITHOUT DOOR 24" RF70F23DER 23 cu. ft. Bespoke Counter Depth 4-Doo

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

28.75 in · Fit role: Traffic projection. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_less_handles_in = closed appliance depth because the documented design has no projecting exterior handle

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: No projecting exterior handle; depth less handles equals closed overall depth 28.75 in
Reviewed: 2026-09-04

No projecting exterior handle; depth less handles equals closed overall depth 28.75 in

Why this value was used

No projecting exterior handle; depth less handles equals closed overall depth 28.75 in Calculation or inference: depth_less_handles_in = closed appliance depth because the documented design has no projecting exterior handle.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

28.75 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions with hinges and doors: depth 28 3/4 in
Reviewed: 2026-09-04

Dimensions with hinges and doors: depth 28 3/4 in

Why this value was used

Dimensions with hinges and doors: depth 28 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

43 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — RF70F23DER_V8_merged_specs.pdf
www.theinsidersnet.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: DEPTH WITH D00R OPEN 90° = 43.0 in | 6" OPENING) 35 3/ 4 " D TOP OF REFRIGERATOR WITH DRAWER OPEN AN
Reviewed: 2026-09-04

DEPTH WITH D00R OPEN 90° = 43.0 in | 6" OPENING) 35 3/ 4 " D TOP OF REFRIGERATOR WITH DRAWER OPEN AND DOORS OPEN 90° DEPTH WITH D00R OPEN 90° 43" DEPTH WITH DRAWER OPEN 441/ 2" 2 1/ 8" NOTE: Please allow 3¾" of clearance when

Why this value was used

DEPTH WITH D00R OPEN 90° = 43.0 in | 6" OPENING) 35 3/ 4 " D TOP OF REFRIGERATOR WITH DRAWER OPEN AND DOORS OPEN 90° DEPTH WITH D00R OPEN 90° 43" DEPTH WITH DRAWER OPEN 441/ 2" 2 1/ 8" NOTE: Please allow 3¾" of clearance when

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — a4fd3effcdb1024963c267b690ea505f74f4f27db09b1ca8ebd3e591c095bf57.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-09-25

The document states that a 36 in opening fits this 35 3/4 in wide refrigerator. Replaces the calculated 36 1/2 in.

Why this value was used

The document states that a 36 in opening fits this 35 3/4 in wide refrigerator. Replaces the calculated 36 1/2 in.

Other evidence found

• 36.5 in — superseded

  images.thdstatic.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 36.5 in — superseded

  images.thdstatic.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗
• 36.5 in — superseded

  images.thdstatic.com; location not retained. Model scope: not separately recorded. Raw value: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — RF70F23DER_V8.pdf
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

26 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa
Samsung · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 24.0 in plus propagated rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF70F23DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF70F23DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top for ease of installation."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — RF70F23DER_V8.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s
Reviewed: 2026-09-05

Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value.

Why this value was used

Exact-model cached Samsung clearance statement: top_clearance_in=0.375 in; 4 copy/copies, 2 domain(s), official=True; no contrary parsed value.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — rf8000bc-3-door-french-door-autofill-pitcher-24-cu-ft-silver-rf24bb6200qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original e
Reviewed: 2026-09-05

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back

Why this value was used

Conflict-free corporate-family exact 8-dimension chassis match to Samsung RF24BB6200QLAA; original evidence: 2 inches of space in the back Calculation or inference: exact 8-dimension chassis signature; source model Samsung RF24BB6200QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

3.75 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 2
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 3.75" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

11.375 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — a4fd3effcdb1024963c267b690ea505f74f4f27db09b1ca8ebd3e591c095bf57.pdf
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Page 3
Reviewed: 2026-10-15

Will-it-fit sheet "MODEL RF70F23DER DIMENSIONS", "TOP OF REFRIGERATOR WITH DOORS OPEN 125°": each door reaches 11 3/8 in past the cabinet side (58 1/2 in overall = 35 3/4 + 2 x 11 3/8). The sheet's 3 3/4 in note is the 90-degree handle clearance, stored as wall_clearance_door_90_in. The spec sheets (RF70F23DER_V8 and V10, p.2) and the user manual (p.20, RF70F23*: 125°, 58 2/4 in, 11 3/8 in / 289 mm) print the same.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

Will-it-fit sheet "MODEL RF70F23DER DIMENSIONS", "TOP OF REFRIGERATOR WITH DOORS OPEN 125°": each door reaches 11 3/8 in past the cabinet side (58 1/2 in overall = 35 3/4 + 2 x 11 3/8). The sheet's 3 3/4 in note is the 90-degree handle clearance, stored as wall_clearance_door_90_in. The spec sheets (RF70F23DER_V8 and V10, p.2) and the user manual (p.20, RF70F23*: 125°, 58 2/4 in, 11 3/8 in / 289 mm) print the same.

Other evidence found

• 3.75 in — superseded

  Document 61dec54c62c2f9f4578f3152f25f116ebc0c8e46710417567d4fd39b547f87f0.pdf; page 2. Model scope: not separately recorded. Raw value: Installation along a wall: 3 3/4 in, with the diagram showing the doors fully open to 125 degrees.. The final reviewed registry supersedes this earlier audit value.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — f63c2a21-e261-4217-990a-09a6dfc5c443.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and doors: width 35 3/4 in
Reviewed: 2026-09-04

Dimensions without hinges and doors: width 35 3/4 in

Why this value was used

Dimensions without hinges and doors: width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.