Measurement evidence for Samsung RF31CG7200SR

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Product width 35 3/4 in
Reviewed: 2026-09-04

Product width 35 3/4 in

Why this value was used

Product width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and door: height 68 7/8 in
Reviewed: 2026-09-04

Dimensions without hinges and door: height 68 7/8 in

Why this value was used

Dimensions without hinges and door: height 68 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 20e199a1-4f71-4213-a7db-76254f9a3f52.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 90° 48 1/ 2" [...] DEPTH TO DOOR HANDLE 361/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator S
Reviewed: 2026-09-04

90° 48 1/ 2" [...] DEPTH TO DOOR HANDLE 361/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator Standard-depth refrig

Why this value was used

90° 48 1/ 2" [...] DEPTH TO DOOR HANDLE 361/ 4 " HEIGHT WITH HINGE 70" Standard-Depth Refrigerator Standard-depth refrig

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.5 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and door: depth 29 1/2 in
Reviewed: 2026-09-04

Dimensions without hinges and door: depth 29 1/2 in

Why this value was used

Dimensions without hinges and door: depth 29 1/2 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

33.875 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions with hinge and door, no handle: depth 33 7/8 in
Reviewed: 2026-09-04

Dimensions with hinge and door, no handle: depth 33 7/8 in

Why this value was used

Dimensions with hinge and door, no handle: depth 33 7/8 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions with hinges, handles and doors: depth 36 1/4 in
Reviewed: 2026-09-04

Dimensions with hinges, handles and doors: depth 36 1/4 in

Why this value was used

Dimensions with hinges, handles and doors: depth 36 1/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: 90-degree top-view product depth 48 1/2 in; separate 53 in drawer-open dimension
Reviewed: 2026-09-04

90-degree top-view product depth 48 1/2 in; separate 53 in drawer-open dimension

Why this value was used

90-degree top-view product depth 48 1/2 in; separate 53 in drawer-open dimension

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.5

Confidence label: high.

Calculation inputs: Overall width; Left-side ventilation clearance;

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearan
Reviewed: 2026-09-18

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged.

Why this value was used

Reviewed product width and per-side installation clearance; width_doors_closed_in + 2 * side_clearance_wall_in = 36.5 in | Formula text updated 2026-09-18: the side gap it used was the side ventilation clearance (side_clearance_wall_in was retired); the value is unchanged. Calculation or inference: width_doors_closed_in + 2 * side_ventilation_clearance_in = 36.5.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 20e199a1-4f71-4213-a7db-76254f9a3f52.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Minimum opening depth derived from case-only depth 29.5 in plus documented rear clearance 2.0 in.
Reviewed: 2026-09-05

Minimum opening depth derived from case-only depth 29.5 in plus documented rear clearance 2.0 in.

Why this value was used

Minimum opening depth derived from case-only depth 29.5 in plus documented rear clearance 2.0 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: medium.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF30BB6600QLAA

Confidence label: medium.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF30BB6600QLAA: Cached exact-model result: Allo
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF30BB6600QLAA: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Samsung documented sibling/platform propagation from RF30BB6600QLAA: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top Calculation or inference: shared Samsung model family; evidence donor RF30BB6600QLAA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: resolved fraction/unit/scenario semantics from cached full-page evidence

Confidence label: high.

Primary evidence

Samsung measurement source — 20e199a1-4f71-4213-a7db-76254f9a3f52.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: full-page adjudication=2.0; parser candidates=[2.0, 1.0]; 2" minimum clearance at rear
Reviewed: 2026-09-05

full-page adjudication=2.0; parser candidates=[2.0, 1.0]; 2" minimum clearance at rear

Why this value was used

full-page adjudication=2.0; parser candidates=[2.0, 1.0]; 2" minimum clearance at rear

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

4.25 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 6cfe70e6d24b09237e6ac5e8c01c2d04ddbf559770c748e2476b0d9c64c1fb7d.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Page 1
Reviewed: 2026-10-03

Allow 4 1/4 in of clearance to enable doors to open 90 degrees when installed next to a wall. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

Why this value was used

Allow 4 1/4 in of clearance to enable doors to open 90 degrees when installed next to a wall. The largest door-swing clearance printed for this model is stored (owner rule for clearances); the spec sheets' 2.5 in is where the handle may touch the wall.

Other evidence found

• 2.5 in — superseded

  images.thdstatic.com; page 2. Model scope: not separately recorded. Raw value: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). 2. Refer to illustration below to determine dimensions. | 3. Allow 2.5" of clearance on hinge side of refrigerator when installing next to a wall | where handle may make contact.. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — ed9b4347-bd1a-4e5e-ba8a-1584d71bc456.pdf
images.thdstatic.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Dimensions without hinges and door: width 35 3/4 in
Reviewed: 2026-09-04

Dimensions without hinges and door: width 35 3/4 in

Why this value was used

Dimensions without hinges and door: width 35 3/4 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.