Measurement evidence for Samsung RF30BB6600QLAA

Value used by ExactFit

35.75 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm
Reviewed: 2026-09-04

Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70 inch - Net Case Height without Hinge 68.875 i

Why this value was used

Net Width: 35.75 in | (WxHxD) 35.8 x 70.0 x 34.3 inches - Net Dimension (WxHxD) 908 x 1778 x 870 mm - Net Width (inch) 35.75 inch - Net Case Height with Hinge 70 inch - Net Case Height without Hinge 68.875 i

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

68.875 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Case Height without Hinge 68.875 in.
Reviewed: 2026-09-04

Official exact-model page: Net Case Height without Hinge 68.875 in.

Why this value was used

Official exact-model page: Net Case Height without Hinge 68.875 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Case Height with Hinge 70 in.
Reviewed: 2026-09-04

Official exact-model page: Net Case Height with Hinge 70 in.

Why this value was used

Official exact-model page: Net Case Height with Hinge 70 in.

Other evidence found

• 73 in — superseded

  image-us.samsung.com; location not retained. Model scope: not separately recorded. Raw value: cu. ft. Kimchi & Specialty French Door - Samsung HEIGHT WITH HINGE 73" DEPTH WITHOUT DOOR 25 5/ 8 " DEPTH TO DOOR HANDLE. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

29.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door 29.375 in.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door 29.375 in.

Why this value was used

Official exact-model page: Net Depth without Door 29.375 in.

Other evidence found

• 24 in — superseded

  image-us.samsung.com; location not retained. Model scope: not separately recorded. Raw value: HINGE 70 3/ 4" WIDTH (FITS 36" OPENING) 35 7/ 8" DEPTH WITHOUT DOOR 24 " 59" 125° 125° TOP OF REFRIGERATOR WITH DOORS OPEN. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Official exact-model page: Net Depth without Door Handle 34.25 in.
Reviewed: 2026-09-04

Official exact-model page: Net Depth without Door Handle 34.25 in.

Why this value was used

Official exact-model page: Net Depth without Door Handle 34.25 in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

34.25 in · Fit role: Traffic projection.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Depth with Door Handle: 34.25 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.
Reviewed: 2026-09-04

Depth with Door Handle: 34.25 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 34.25 inch - Net Depth without Door Handle 34.25 inch - Net Depth without Door 29.375 in

Why this value was used

Depth with Door Handle: 34.25 in | ase Height with Hinge 70 inch - Net Case Height without Hinge 68.875 inch - Net Depth with Door Handle 34.25 inch - Net Depth without Door Handle 34.25 inch - Net Depth without Door 29.375 in

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is traffic projection. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

48.5 in · Fit role: Operating clearance. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: same-brand product-class chassis propagation from RF30BB660012AA

Confidence label: medium.

Primary evidence

Samsung measurement source — samsung-rf30bb660012aa
www.shopappliances.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_
Reviewed: 2026-09-04

Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_90_in=48.5 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Depth with Door Opened at 90 Degrees = 48.5 in | | 35 3/4" | | Depth | | Depth | 34 1/4" | | Depth without Handles | 34 1/4" | | Depth with Door Opened at 90 Degrees | 48 1/2" | | Counter-Depth | No | | Height | | Height | 70" | | Height without Hinges |

Why this value was used

Medium-confidence chassis inference from RF30BB660012AA. Donors unanimously report depth_doors_open_90_in=48.5 in; at least four direct chassis dimensions match and none conflict. Matching fields: width_doors_closed_in, height_case_in, height_hinge_in, depth_case_only_in, depth_less_handles_in, depth_with_handles_in. Donor evidence: Depth with Door Opened at 90 Degrees = 48.5 in | | 35 3/4" | | Depth | | Depth | 34 1/4" | | Depth without Handles | 34 1/4" | | Depth with Door Opened at 90 Degrees | 48 1/2" | | Counter-Depth | No | | Height | | Height | 70" | | Height without Hinges | Calculation or inference: same-brand product-class chassis propagation from RF30BB660012AA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

36.5 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375

Confidence label: medium.

Primary evidence

Samsung measurement source — rf8000b-3-door-french-door-beverage-center-30-cu-ft-silver-rf30bb6600qlaa + side gap from the maker's document
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Retained specification excerpt: Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on
Reviewed: 2026-09-04

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side.

Why this value was used

Derived minimum opening width 36.5 in from product width 35.75 in and explicit 0.375 in clearance on each side. Calculation or inference: max(case width, width doors closed) + 2 * explicit side clearance = 35.75 + 2 * 0.375.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

70.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: max(height_case_in,height_hinge_in) + top_clearance_in

Confidence label: medium.

Calculation inputs: Cabinet height; Height with hinge / controlling height; Top clearance;

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in.

Why this value was used

Samsung installation envelope: 70 in appliance endpoint + 0.375 in clearance = 70.375 in. Calculation or inference: max(height_case_in,height_hinge_in) + top_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

31.375 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: depth_case_only_in + rear_clearance_in

Confidence label: medium.

Calculation inputs: Depth without door; Rear clearance;

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in.
Reviewed: 2026-09-05

Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in.

Why this value was used

Samsung installation envelope: 29.375 in appliance endpoint + 2 in clearance = 31.375 in. Calculation or inference: depth_case_only_in + rear_clearance_in.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides an
Reviewed: 2026-10-29

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Why this value was used

The document this model's measurements come from states: "Allow a 3/8" minimum clearance at sides and top."

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the width comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

0.375 in · Fit role: Cavity fit.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Cached exact-model result: Allow a 3/8" minimum clearance at sides and top
Reviewed: 2026-09-05

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Why this value was used

Cached exact-model result: Allow a 3/8" minimum clearance at sides and top

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the height comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2 in · Fit role: Cavity fit. Calculated or inferred value — not a directly printed measurement.

Original published value and unit: see retained transcription below. Normalization: shared Samsung model family; evidence donor RF30BB660012AA

Confidence label: medium.

Primary evidence

Samsung measurement source — 62060280-manufacturer's-brochure.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Samsung documented sibling/platform propagation from RF30BB660012AA: full-page adjudication=2.0; par
Reviewed: 2026-09-05

Samsung documented sibling/platform propagation from RF30BB660012AA: full-page adjudication=2.0; parser candidates=[2.0, 1.0]; 2" minimum clearance at rear

Why this value was used

Samsung documented sibling/platform propagation from RF30BB660012AA: full-page adjudication=2.0; parser candidates=[2.0, 1.0]; 2" minimum clearance at rear Calculation or inference: shared Samsung model family; evidence donor RF30BB660012AA.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This measurement supports the depth comparison. An applicable cutout can replace additive clearances. If a required input is unknown and no applicable alternative requirement is established, the result is Uncertain unless another known requirement proves Does not fit.

Value used by ExactFit

2.5 in · Fit role: Operating clearance.

Original published value and unit: see retained transcription below. Normalization:

Confidence label: high.

Primary evidence

Samsung measurement source — 62059894-assembly-instructions.pdf
www.nfm.com · Web source
Model scope: Secondary source
Publication/revision date: Not recorded
Location: Retained specification excerpt: Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model
Reviewed: 2026-09-17

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 2.5" of clearance on hinge side

Why this value was used

Migrated from hinge_side_wall_clearance_in (door angle not stated, 6 in or less). Cached exact-model result: Allow 2.5" of clearance on hinge side

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

Unknown · Fit role: Operating clearance.

Primary evidence

Source not recorded
Publisher not recorded · Retained document
Model scope: Not established
Publication/revision date: Not recorded
Location: Exact location not retained
Reviewed: Not recorded

No retained excerpt is available.

The original source link has not yet been recovered from the retained records. This is a link-recovery gap, not a missing measurement. The final registry-verified value and audit text remain available above.

Why this value was used

No evidence decision recorded.

Other evidence found

No materially different value is retained in the linked per-measurement audit records. This does not imply that every published source was searched.

Effect on fit result

This is operating clearance. It is shown for a separate on-site check and does not establish cavity fit or delivery access.

Value used by ExactFit

35.75 in · Fit role: Informational only.

Original published value and unit: see retained transcription below. Normalization: No separate conversion rule recorded; the stored normalized value is retained without additional rounding.

Confidence label: high.

Primary evidence

Samsung measurement source — 105583859.pdf
Samsung · Web source
Model scope: Exact model
Publication/revision date: Not recorded
Location: Page 19
Reviewed: 2026-10-03

Clearance table for RF30BB6*****: width B 35 6/8 in (908 mm). The stored 35 in came from a retail net-width figure.

Why this value was used

Clearance table for RF30BB6*****: width B 35 6/8 in (908 mm). The stored 35 in came from a retail net-width figure.

Other evidence found

• 35 in — superseded

  www.samsung.com; location not retained. Model scope: not separately recorded. Raw value: Official Samsung cached specification: case_width_in = 35.0 in; source_id=27527. The final reviewed registry supersedes this earlier audit value.

  Open alternative source ↗

Effect on fit result

This is informational only. It is shown for a separate on-site check and does not establish cavity fit or delivery access.